SID Volvo FH4

————————————————————————————————————————————————————————————

U200A88

Communication error on Display Subnet

Bus off

No communication is possible to the Secondary Information Display (SID). The SID can not receive any data on the CAN-network. The SID keep the last recevied VehicleMode

– CAN High Short Circuit to ground

– CAN High short circuit to CAN Low

– Open circuit CAN High

– Open Circuit CAN Low

– Connector damaged

– Connector disconnected

– Transciever damaged

Diagnostic Service 14. No additional action is needed.

Investigate root-cause:

– CAN-network error => Fix problem.

– CAN-cable => Fix problem. Transceiver failure => Replace ECU

CAN Communication Display Net

————————————————————————————————————————————————————————————

U300041

Internal EEPROM failure

General Checksum Failure

Enter limp-home mode. Cluster will be black except for STOP Lamp which will be lit.

Memory Failure.  Incorrect checksum of the memory

where the patchable data is

stored.

Diagnostic Service 14. No additional action is needed.

Replace ECU

Electronic control unit

Node

DTC ISO

FailureEvent

FTB_Name

FunctBehaviorDesc

PossibleRootCause

ProcedureEraseConfirmedDtc

ProposedWorkshopAction

ProprietaryName

————————————————————————————————————————————————————————————

U300044

Internal RAM failure

Data Memory Failure

No controlled reduced functionality due to that the DTC is set.

Normal functionality can not be guaranteed when

this DTC is set.

Memory failure

Diagnostic Service 14. No additional action is needed.

Replace ECU

Electronic control unit

————————————————————————————————————————————————————————————

U300045

Internal ROM failure

Program Memory Failure

No controlled reduced functionality due to that the DTC is set.

Normal functionality can not be guaranteed when

this DTC is set.

Memory failure

Diagnostic Service 14. No additional action is needed.

1. Reflash software

2. If failure still present, replace unit

Electronic control unit

————————————————————————————————————————————————————————————

U300049

Internal electronic failure

Internal Electronic Failure

No controlled reduced functionality due to that the DTC is set.

Normal functionality can not be guaranteed when

this DTC is set.

-CAN-tranciever error

Diagnostic Service 14. No additional action is needed.

Replace Instrument Cluster.

Electronic control unit

————————————————————————————————————————————————————————————

U30004B

Temperature of TFT Display > 70 degrees Celcius

Over Temperature

ECU (IC) will set the background illumination level to Max 25% to cool

down.

High environmental temperature

Diagnostic Service 14. No additional action is needed.

Investigate driving environment – is truck being driven in very hot climate? Investigate other nearby components – is another component running very hot?

Electronic control unit

————————————————————————————————————————————————————————————

U300094

Application performs an unexpected operation

Unexpected Operation

No controlled reduced functionality due to that the DTC is set.

Normal functionality can not be guaranteed when

this DTC is set.

Watch dog reset ( software

/ parameter bug ) Sudden loss of power

Diagnostic Service 14. No additional action is needed.

Talk to driver

1. Can indicate improper shutdown – see possible root causes, no Instrument Cluster action required

2. If Cluster has been behaving strangely reflash Instrument Cluster

Electronic control unit

————————————————————————————————————————————————————————————

U300098

Temperature of TFT display > 65 degrees Celsius

Component or System Over Temperature

ECU (IC) will set the background illumination level to Max 50% to cool

down.

High environmental temperature

Diagnostic Service 14. No additional action is needed.

Investigate driving environment – is truck being driven in very hot climate? Investigate other nearby components – is another component running very hot?

Electronic control unit

————————————————————————————————————————————————————————————

U300316

Circuit Voltage Below Threshold. Considering component tolerances the fault will be detected between 7,7V   ,9V

Circuit Voltage Below Threshold

All functionalities are switched off (including the illumination of the SID).

Normal functionality can not be guaranteed when this DTC is set.

Voltage supply too low

Diagnostic Service 14. No additional action is needed.

Check other ECUs for DTC

Read battery voltage from other ECUs

Check integrity of power and ground lines to IC.

Battery Power

————————————————————————————————————————————————————————————

U300317

Circuit Voltage Above Threshold. Considering component tolerances the fault will be detected between         32,1        ,7V

Circuit Voltage Above Threshold

All functionalities are switched off (including the illumination of the SID).

Normal functionality can not be guaranteed when this DTC is set.

Voltage supply too high

Diagnostic Service 14. No additional action is needed.

Check other ECUs for DTC

Read battery voltage from other ECUs

Check integrity of power and ground lines to IC.

Battery Power

————————————————————————————————————————————————————————————

U114863

Continuous touch screen press events for >= 10 seconds

Circuit / Component Protection Time-Out

SID will notify other ECU that touch screen information is not reliable anymore by sending “Error” coordinates

– Touch screen pressed / struck for a long time (for atleast 10 seconds continuously)

– Touch screen faulty

Diagnostic Service 14. No additional action is needed.

Verify that no objects are put on the touch screen. If not, replace ECU

Touch Screen Display Module

————————————————————————————————————————————————————————————

U114768

The number of DTC’s set in the ECU has reached 29

Event Information

No reduced functionality due to that the DTC is set.

To many internal diagnostic trouble codes set in the ECU.

Diagnostic Service 14. No additional action is needed.

Clear DTCs

DTC Notification Max Limit Reached

Node

DTC ISO

FailureEvent

FTB_Name

FunctBehaviorDesc

PossibleRootCause

ProcedureEraseConfirmedDtc

ProposedWorkshopAction

ProprietaryName

————————————————————————————————————————————————————————————

P000041

Program memory corruption.

General Checksum Failure

Application should not start (remains in boot-mode).

Cluster will be black except for STOP Lamp which will be lit.

Memory Failure.  Incorrect checksum of the memory.

Diagnostic Service 14. No additional action is needed.

Replace ECU.

Control Module

————————————————————————————————————————————————————————————

U1FFF68

Factory Mode is active in the ECU.

Event Information

No reduced functionality due to that the DTC is set.

Factory Mode is active in the ECU.

Whenever P1C54 parameter is set to TRUE, this DTC shall

be set.

Diagnostic Service 14. No additional action is needed.

Write parameter P1C54 to false

Factory Mode Active

————————————————————————————————————————————————————————————

U114998

Ambient Temperature > +85 degrees C during Vehicle Operation

Component or System Over Temperature

None

Ambient Temperature is High

Ambient Temperature Sensor Fault

Diagnostic Service 14. No additional action is needed.

Investigate driving environment – is truck being driven in very hot climate? Investigate other nearby components – is another component running very hot?

Ambient Air Temperature

————————————————————————————————————————————————————————————

U114608

LVDS

communication error with Secondary information Display

Bus Signal / Message Failures

No controlled reduced functionality due to that the DTC is set.

Normal functionality can not be guaranteed when

this DTC is set.

Low Level failure on LVDS Communication

LVDS communication link error or LVDS internal hardware error

Diagnostic Service 14. No additional action is needed.

Check integrity of LVDS cable

Ensure LVDS cable is connected properly both at SID and Video Switch Check Video Switch for DTCs

LVDS Video Data Circuit

————————————————————————————————————————————————————————————

B150363

Push button error:

-GPIO(General Purpose Input/Output) pin is read as 1

continuously for 30

seconds

Circuit / Component Protection Time-Out

One button can no longer be used.

One of the push buttons from SID is stucked.

Internal SID hardware failure.

Diagnostic Service 14. No additional action is needed.

Replace ECU

Secondary Infotainment Display Button Switches

Skype
Telegram
WhatsApp
Email

Политика    Контакты

© Copyright 2025 DTCON.EU Powered by VHF84
© Copyright 2025 DTCON.EU Powered by VHF84
© Copyright 2025 DTCON.EU Powered by VHF84
error: Внимание: Контент защищён!