————————————————————————————————————————————————————————————
U000188
It has not been possible to send frames on High Speed CAN Communication Bus and It has not been possible to receive frames on High Speed CAN Communication Bus
Bus off
.
Diagnostic Service 14. No additional action is needed
.
CAN Communication Backbone 2 Net
————————————————————————————————————————————————————————————
U001088
It has not been possible to send frames on Medium Speed CAN Communication Bus and It has not been possible to receive frames on Medium Speed CAN Communication Bus
Bus off
.
Diagnostic Service 14. No additional action is needed
.
CAN Communication Backbone 1 Net
————————————————————————————————————————————————————————————
U010187
Missing Message
ETC2 not responding
.
Diagnostic Service 14. No additional action is needed
Check:
ETC2 not responding
Lost Communication with TECU
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P034031
No Signal
The engine start time will increase.
Possible loss of power
Sensor/Harness Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Camshaft Position Sensor “A” Bank 1 or Single
Sensor
————————————————————————————————————————————————————————————
P034138
Signal Frequency Incorrect
The engine start time will increase.
Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Camshaft Position Sensor A Circuit
Range/Performance
————————————————————————————————————————————————————————————
P052612
Measured voltage above limit
Circuit Short To Battery
Either
1. Fan will work as on/off fan. 100% fan speed if cooling is needed. Higher fuel consumption.
Or
2. Fan will work in open loop mode. Deteriorated fan control, but might not be noticable to driver.
Broken sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Fan Speed Sensor Circuit
————————————————————————————————————————————————————————————
P054300
Measured voltage outside the limits specified by the sensor
No Sub Type Information
Might get start problems in cold climate.
Heating element or wire broken.
Preheat sense 1
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1
Intake Air Heater A Circuit Open
————————————————————————————————————————————————————————————
P054415
Measured voltage outside the limits specified by the sensor
Circuit Short To Battery or Open
Fault code set by ACM: IDTC_ENGEXHTEMP_OC
Diagnostic Service 14. No additional action is needed
Check:
Fault code set by ACM: IDTC_ENGEXHTEMP_OC
Exhaust Gas Temperature Sensor Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P001676
Wrong Mounting Position
Fuel consumption increased
Bad correlation between cam and crank, engine transmission not correct
Engine transmission
Diagnostic Service 14. No additional action is needed
Check:
Engine transmission
Crankshaft Position – Camshaft Position Correlation
————————————————————————————————————————————————————————————
P007100
No Sub Type Information
Ambient air temp sensor or boost temp sensor faulty Ambient air temp sensor or Boost temp sensor
Diagnostic Service 14. No additional action is needed
Check:
Ambient air temp sensor or Boost temp sensor
Ambient Air Temperature Sensor Range/Performance
————————————————————————————————————————————————————————————
P02CD00
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 1 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02CF00
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 2 Fuel Injector Offset Learning at Max Limit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P02D100
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 3 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D300
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 4 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D500
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 5 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D700
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 6 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P033531
No Signal
Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running. Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankshaft Position Sensor “A”
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P033638
Signal Frequency Incorrect
Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running. Possible loss of power
Sensor monting Sensor/Lack of shims
Diagnostic Service 14. No additional action is needed
Check:
Sensor/Lack of shims
Crankshaft Position Sensor A Circuit Range/Performance
————————————————————————————————————————————————————————————
P033900
No Sub Type Information
The engine start time will increase.Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running.
Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankshaft Position Sensor A Circuit Intermittent
————————————————————————————————————————————————————————————
P203F00
No Sub Type Information
No urea dosing
Urea symbol in cluster
Tank almost empty, stop dosing to maintain cooling ECM interpretation of raw value. Urea level. DST problem.
Diagnostic Service 14. No additional action is needed
Check:
ECM interpretation of raw value. Urea level. DST problem.
Reductant Level Low
————————————————————————————————————————————————————————————
P205A13
Measured voltage outside the limits specified by the sensor
Circuit Open
None
AdBlue tank temp sensor Cables
Connectors
Urea tank temp sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor, Cables, Connectors
Reductant Tank Temperature Sensor
————————————————————————————————————————————————————————————
P208064
Signal Plausibility Failure
None
The sensor is not plausible Leakage in exhaust system Leakage in intake system Sensor
Diagnostic Service 14. No additional action is needed
Check:
Leakage in exhaust system Leakage in intake system Sensor
Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P220013
Measured voltage outside the limits specified by the sensor
Circuit Open
Cabling between Nox- sensor and Nox-sensor ECU Nox-sensor
Nox-sensor cabling Nox-sensor
Diagnostic Service 14. No additional action is needed
Check:
Nox-sensor cabling Nox-sensor
NOx Sensor Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P220164
Signal Plausibility Failure
Excessive urea dosing (only for SCR system)
Exhaust system leakage Air intake leakage
Nox-sensor
Dosing system (only for SCR system)
Exhaust system Air intake system
Nox-sensor
Diagnostic Service 14. No additional action is needed
Check:
Dosing system (only for SCR system) Exhaust system
Air intake system Nox-sensor
NOx Sensor Circuit Range/Performance
————————————————————————————————————————————————————————————
P060100
No Sub Type Information
Engine derate
signature failure
.
Diagnostic Service 14. No additional action is needed
Check: signature failure
Internal Control Module Memory Check Sum Error
————————————————————————————————————————————————————————————
P060700
No Sub Type
Information
Not possible to reprogram
ECU
.
Diagnostic Service 14. No additional
action is needed
.
Control Module
Performance
————————————————————————————————————————————————————————————
P06151C
Measured voltage outside the limits specified by the sensor
Circuit Voltage Out of Range
Impossible to activate starter motor
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P061600
Measured voltage
below limit
No Sub Type
Information
EMS can not control starter
Start relay/harness
Diagnostic Service 14. No additional
action is needed
Check:
Start relay/Harness
Starter Relay Circuit Low
————————————————————————————————————————————————————————————
P061700
Measured voltage above limit
No Sub Type Information
Impossible to activate starter motor.
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Circuit High
————————————————————————————————————————————————————————————
P066800
Measured voltage below limit
No Sub Type Information
None
Internal fault in ECM ECM
Diagnostic Service 14. No additional action is needed
Check: ECM
PCM/ECM/TCM Internal
Temperature Sensor Circuit Low
————————————————————————————————————————————————————————————
P06B100
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply A Circuit Low
————————————————————————————————————————————————————————————
P06B200
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply A Circuit High
————————————————————————————————————————————————————————————
P06B400
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply B Circuit Low
————————————————————————————————————————————————————————————
P06B500
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply B Circuit High
————————————————————————————————————————————————————————————
P20EE00
No Sub Type Information
NOx-conversion reduced by appr. 50%
Possible ammonia smell
Regent out of specification, Dosing performance low Urea specification
Dosing system
Diagnostic Service 14. No additional action is needed
Check:
Urea specification Dosing system
SCR NOx Catalyst Efficiency Below Threshold (Bank 1)
————————————————————————————————————————————————————————————
P260013
Measured voltage outside the limits specified by the sensor
Circuit Open
Pump always at half speed. High coolant temperatures may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Coolant Pump Control Circuit/Open
————————————————————————————————————————————————————————————
P260200
Measured voltage below limit
No Sub Type Information
Pump always runs at full speed. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Coolant Pump Control Circuit Low
————————————————————————————————————————————————————————————
P260300
Measured voltage above limit
No Sub Type Information
Pump always at half speed. High coolant temperatures may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Coolant Pump Control Circuit High
————————————————————————————————————————————————————————————
P261087
Missing Message
Timestamps from Cluster not available
J1708 time data failure and J1939 message does not exist. (Cluster error).
Cluster
Diagnostic Service 14. No additional action is needed
Check: Cluster
ECM/PCM Internal Engine Off Timer Performance
————————————————————————————————————————————————————————————
P2BA700
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Empty Reagent Tank
————————————————————————————————————————————————————————————
P023400
No Sub Type Information
Too high pressure Turbine , Compressor
Diagnostic Service 14. No additional action is needed
Check:
Turbine , Compressor
Turbocharger/Supercharg er Overboost Condition
————————————————————————————————————————————————————————————
P029900
No Sub Type Information
Too low pressure
Boost leakage, wastegate, VGT, compressor.
Diagnostic Service 14. No additional action is needed
Check:
Boost leakage, wastegate, VGT, compressor.
Turbocharger/Supercharg er Underboost
————————————————————————————————————————————————————————————
U300001
Measured voltage outside the limits specified by the sensor
General Electrical Failure
Possible damage on EMS system components depending on the high voltage (>36V)
Generator, external charger
Diagnostic Service 14. No additional action is needed
Check:
Generator, external charger
Electronic control unit
————————————————————————————————————————————————————————————
U300041
Program memory corruption
General Checksum Failure
The engine can not be started
No software Software download
application
Diagnostic Service 14. No additional action is needed
Check:
Software download application
Electronic control unit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P007087
Missing Message
None
J1708 and CAN ambient air temperature message does not exist.
Harness. Cluster
Diagnostic Service 14. No additional action is needed
Check:
Harness. Cluster
Ambient Air Temperature Sensor “A”
————————————————————————————————————————————————————————————
P011013
Measured voltage outside the limits specified by the
sensor
Circuit Open
Engine is running but could be difficult to start in cold climate.
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Intake Air Temperature Sensor 1 Bank 1
————————————————————————————————————————————————————————————
P011200
Measured voltage below limit
No Sub Type Information
Engine is running but could be difficult to start in cold climate.
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Intake Air Temperature Sensor 1 Circuit Low Bank 1
————————————————————————————————————————————————————————————
P011700
Measured voltage below limit
No Sub Type Information
Engine is difficult to start. Idle run regulation is
detoriated.
Harness Sensor
Sensor/Harness
Diagnostic Service 14. No additional action is needed
Check: Sensor/Harness
Engine Coolant Temperature Circuit Low
————————————————————————————————————————————————————————————
P021700
No Sub Type Information
Powerloss
Extreme Driving conditions Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Engine Coolant Over Temperature Condition
————————————————————————————————————————————————————————————
P048013
Measured voltage outside the limits specified by the sensor
Circuit Open
Fan runs at full speed. Increased fuel consumption may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit
————————————————————————————————————————————————————————————
P051B64
Signal Plausibility Failure
Powerloss (minor) P3524:
Black smoke (minor)
The crank case pressure is showing either too high or to low value.
(abnormal value) Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor ECM
Engine High Resolution Crankcase Pressure Circuit Range/Performance
————————————————————————————————————————————————————————————
P051A13
Measured voltage outside the limits specified by the sensor
Circuit Open
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankcase Pressure Sensor
————————————————————————————————————————————————————————————
P051D00
Measured voltage above limit
No Sub Type Information
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine High Resolution Crankcase Pressure
————————————————————————————————————————————————————————————
P052300
Measured voltage above limit
No Sub Type Information
Oil pressure shows 0 in the cluster. Engine is running.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Pressure Circuit High
————————————————————————————————————————————————————————————
P052400
No Sub Type Information
Low pressure, powerloss
Oil leakage, broken oil pump, clogged oil system Oil system
Diagnostic Service 14. No additional action is needed
Check:
Oil system
Engine Oil Pressure Too Low
————————————————————————————————————————————————————————————
P222800
Measured voltage below limit
No Sub Type Information
None
Internal fault in ECM Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor ECM
Barometric Pressure Circuit Low
————————————————————————————————————————————————————————————
P222900
Measured voltage above limit
No Sub Type Information
None
Internal fault in ECM Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor ECM
Barometric Pressure Circuit High
————————————————————————————————————————————————————————————
P226400
No Sub Type Information
None
No error: Used for indication
when priming pump is active
None
Diagnostic Service 14. No additional action is needed
Check:
No error: Used for indication when priming pump is active
Water in Fuel Sensor
————————————————————————————————————————————————————————————
P226600
Measured voltage
below limit
No Sub Type
Information
Will give water in fuel
indication.
Harness
Diagnostic Service 14. No additional
action is needed
Check:
Harness
Water In Fuel Indicator
Circuit Low
————————————————————————————————————————————————————————————
P226700
Measured voltage above limit
No Sub Type Information
Undetected water in fuel can lead to engine stop
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Water In Fuel Indicator Circuit High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P250C00
Measured voltage below limit
No Sub Type Information
Oil level can not be measured.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Engine Oil Level Circuit Low
————————————————————————————————————————————————————————————
P250F00
No Sub Type Information
None
Critically low oil level Leakage
Leakage
Sensor
Diagnostic Service 14. No additional action is needed
Check: Leakage Sensor
Engine Oil Level Too Low
————————————————————————————————————————————————————————————
P255613
Measured voltage outside the limits specified by the
sensor
Circuit Open
Coolant level can not be detected.
Harness Harness connector
sensor
Diagnostic Service 14. No additional action is needed
Check: Harness connector
sensor
Engine Coolant Level Sensor/Switch
————————————————————————————————————————————————————————————
P255900
Measured voltage above limit
No Sub Type Information
Coolant level can not be detected.
Harness Harness connector
sensor
Diagnostic Service 14. No additional action is needed
Check: Harness connector
sensor
Engine Coolant Level Circuit High
————————————————————————————————————————————————————————————
P256000
No Sub Type Information
Powerloss
Coolant level below range if not Harness
Coolant system
Diagnostic Service 14. No additional action is needed
Check:
Coolant system
Engine Coolant Level Low
————————————————————————————————————————————————————————————
P108600
No Sub Type Information
None
Low oil level Leakage Leakage
Sensor
Diagnostic Service 14. No additional action is needed
Check: Leakage Sensor
Oil Level Moderately Low
————————————————————————————————————————————————————————————
P20BF00
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Reagent Hose Heater 2 Short Circuit Low
————————————————————————————————————————————————————————————
U014100
Lost communication with the node on Medium Speed CAN Communication Bus
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With VMCU
————————————————————————————————————————————————————————————
U012A87
Lost communication with the node
Missing Message
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With CCIOM
————————————————————————————————————————————————————————————
P109000
No Sub Type Information
Display of the message, without bip, simultaneously with the gear engaged pictogram
Driver started at too high gear at start
Protective alert for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective alert for clutch/transmission
Transmission High Gear At Start
————————————————————————————————————————————————————————————
P208E00
No Sub Type Information
No urea dosing
Sensor/Harness dosing valve
injector, clogged hoses
Diagnostic Service 14. No additional action is needed
Check:
dosing valve
injector, clogged hoses
Aftertreatment Reagent Dosing Valve Clogged
————————————————————————————————————————————————————————————
P109541
General Checksum Failure
Engine derate
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Control Unit
————————————————————————————————————————————————————————————
P109641
General Checksum
Failure
Engine derate
.
Diagnostic Service 14. No additional
action is needed
.
Transmission Control Unit
————————————————————————————————————————————————————————————
P069200
Measured voltage above limit
No Sub Type Information
Fan runs at full speed. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit High
————————————————————————————————————————————————————————————
P069100
Measured voltage below limit
No Sub Type Information
Fan always deactivated or always activated if fault is
intermittent.
Broken actuator, wire or ECM driver output
Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit Low
————————————————————————————————————————————————————————————
U015500
Lost communication with the node on Medium Speed CAN Communication Bus
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With Instrument Panel Cluster (IPC) Control Module
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P052013
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil pressure shows 0 in the cluster. Engine is running.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Pressure Sensor/Switch “A”
————————————————————————————————————————————————————————————
P066613
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Internal fault in ECM ECM
Diagnostic Service 14. No additional action is needed
Check: ECM
Control Module Internal Temperature Sensor “A”
————————————————————————————————————————————————————————————
P020113
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 1 Injector “A”
————————————————————————————————————————————————————————————
P020313
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 3 Injector “A”
————————————————————————————————————————————————————————————
P020413
Measured voltage outside the limits specified by the sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 4 Injector “A”
————————————————————————————————————————————————————————————
P020513
Measured voltage outside the limits specified by the sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 5 Injector “A”
————————————————————————————————————————————————————————————
P020613
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 6 Injector “A”
————————————————————————————————————————————————————————————
P220E93
No Operation
Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
NOx Sensor Heater Control Circuit Range/Performance (Bank
1 Sensor 1)
————————————————————————————————————————————————————————————
P250A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil level can not be measured.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Level Sensor
————————————————————————————————————————————————————————————
P020213
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 2 Injector “A”
————————————————————————————————————————————————————————————
P100E18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 2
————————————————————————————————————————————————————————————
P100F18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 3
————————————————————————————————————————————————————————————
P101018
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 4
————————————————————————————————————————————————————————————
P101518
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 5
————————————————————————————————————————————————————————————
P101618
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 6
————————————————————————————————————————————————————————————
P101711
Measured voltage below limit
Circuit Short To Ground
High fuel consumption due to fuel leakage.
Broken solenoid, wire or ECM driver output
Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P101712
Measured voltage above limit
Circuit Short To Battery
Valve constantly shut.
Broken solenoid, wire or ECM driver output
Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P101713
Measured voltage outside the limits specified by the
sensor
Circuit Open
Valve constantly shut.
Broken solenoid or wire. Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P220300
No Sub Type Information
Cabling between Nox- sensor and Nox-sensor ECU Nox-sensor
Nox-sensor cabling Nox-sensor
Diagnostic Service 14. No additional action is needed
Check:
Nox-sensor cabling Nox-sensor
NOx Sensor Circuit High Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P2BA800
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Interruption of Reagent Dosing Activity
————————————————————————————————————————————————————————————
P2BA900
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Insufficient Reagent Quality
————————————————————————————————————————————————————————————
P2BAA00
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Low Reagent Consumption
————————————————————————————————————————————————————————————
P2BAD00
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Root Cause Unknown
————————————————————————————————————————————————————————————
P2BAE96
Component Internal Failure
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – NOx Control Monitoring System
————————————————————————————————————————————————————————————
P100211
Measured voltage below limit
Circuit Short To Ground
Induction air is hot. Preheat relay is impossible to turn off.
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Preheat Relay
————————————————————————————————————————————————————————————
P100212
Measured voltage above limit
Circuit Short To Battery
Preheat relay not activated. White smoke for cold start. Start problems in cold climate.
Preheat relay solenoid shorted
Preheat relay.
Diagnostic Service 14. No additional action is needed
Check: Preheat relay.
Preheat Relay
————————————————————————————————————————————————————————————
P100213
Measured voltage outside the limits specified by the sensor
Circuit Open
Preheat relay not activated. White smoke for cold start. Start problems in cold climate.
Harness or Preheat relay solenoid
Harness. Preheat relay.
Diagnostic Service 14. No additional action is needed
Check:
Harness. Preheat relay.
Preheat Relay
————————————————————————————————————————————————————————————
P100629
Signal invalid
None
The boost temperature sensor output is showing constant value.
Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Intake Air Temperature Sensor 1 Stuck Bank 1
————————————————————————————————————————————————————————————
P100713
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Pressure switch / Harness Pressure switch/Harness
Diagnostic Service 14. No additional action is needed
Check:
Pressure switch/Harness
Air Filter Indicator
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P100D18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 1
————————————————————————————————————————————————————————————
P102111
Measured voltage below limit
Circuit Short To Ground
VCB can not be turned off. Causes engine to stop.
Engine impossible to
restart.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
P102112
Measured voltage above limit
Circuit Short To Battery
VCB can not be turned on. Engine break function derated. Gear shift performance derated for some automatic transmission boxes.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
P102113
Measured voltage outside the limits specified by the sensor
Circuit Open
VCB can not be turned on. Engine break function derated. Gear shift performance derated for some automatic transmission boxes.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
U010E00
Lost communication with the node
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With Reductant Control
Module
————————————————————————————————————————————————————————————
P019513
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Temperature Sensor “A”
————————————————————————————————————————————————————————————
P204A13
Measured voltage outside the limits specified by the sensor
Circuit Open
No urea dosing
ACM Pump module: AdBlue pressure sensor
ACM Pump module: Internal cabling
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Diagnostic Service 14. No additional action is needed
Check:
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Reductant Pressure Sensor
————————————————————————————————————————————————————————————
P203D00
Measured voltage above limit
No Sub Type Information
None
AdBlue tank level sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
AdBlue tank level sensor, Cables, Connectors
Aftertreatment Reagent Level Short Circuit High
————————————————————————————————————————————————————————————
P208A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
No urea dosing
Wiring harness internal error in pump
Diagnostic Service 14. No additional action is needed
Check:
Wiring harness internal error in pump
Reductant Pump “A” Control
————————————————————————————————————————————————————————————
P026500
Measured voltage above limit
No Sub Type Information
Loss of power and uneven
running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 2 Short Circuit High
————————————————————————————————————————————————————————————
P026800
Measured voltage above limit
No Sub Type Information
Loss of power and uneven
running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 3 Short Circuit High
————————————————————————————————————————————————————————————
P027100
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 4 Short Circuit High
————————————————————————————————————————————————————————————
P027400
Measured voltage above limit
No Sub Type Information
Loss of power and uneven
running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 5 Short Circuit High
————————————————————————————————————————————————————————————
P027700
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 6 Short Circuit High
————————————————————————————————————————————————————————————
P054500
Measured voltage below limit
No Sub Type Information
Fault code set by ACM: IDTC_ENGEXHTEMP_SCL
Diagnostic Service 14. No additional action is needed
Check:
Fault code set by ACM: IDTC_ENGEXHTEMP_SCL
Exhaust Gas Temperature Short Circuit Low
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P20B300
Measured voltage below limit
No Sub Type Information
None
.
Diagnostic Service 14. No additional action is needed
.
Reductant Heater Coolant Control Valve Circuit Low
————————————————————————————————————————————————————————————
P204800
Measured voltage below limit
No Sub Type Information
No urea dosing
ACM Pump module: DCU ACM Pump module: internal cabling
ACM Pump module: DCU,
ACM Pump module: internal cabling
Diagnostic Service 14. No additional action is needed
Check:
ACM Pump module: DCU, ACM Pump module: internal cabling
Aftertreatment Reagent Dosing Valve Short Circuit Low
————————————————————————————————————————————————————————————
P204713
Measured voltage outside the limits specified by the sensor
Circuit Open
no urea dosing
Cable / Connectors
ACM Dosing module: Dosing valve
Cable / Connectors ACM Dosing module: Dosing
valve
Diagnostic Service 14. No additional action is needed
Check:
Cable / Connectors ACM Dosing module: Dosing valve
Reductant Injection Valve Control Bank 1 Unit 1
————————————————————————————————————————————————————————————
P20C300
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Reagent Hose Heater 3 Short Circuit Low
————————————————————————————————————————————————————————————
P20BB00
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Reagent Hose Heater 1 Short Circuit Low
————————————————————————————————————————————————————————————
P20A200
Measured voltage below limit
No Sub Type Information
Not possible to perform afterrun
Internal electrical failure in valve within the ACM
Diagnostic Service 14. No additional action is needed
Check:
Internal electrical failure in valve within the ACM
Aftertreatment Reagent Direction Valve Short
Circuit Low
————————————————————————————————————————————————————————————
P065900
Measured voltage above limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
ACM Actuator High Supply 1 Short Circuit
High
————————————————————————————————————————————————————————————
P065800
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
ACM Actuator High Supply 1 Short Circuit Low
————————————————————————————————————————————————————————————
P208D00
Measured voltage above limit
No Sub Type Information
No urea dosing
Wiring harness internal error in pump
Diagnostic Service 14. No additional action is needed
Check:
Wiring harness internal error in pump
Aftertreatment Reagent
Pump Control Short Circut High
————————————————————————————————————————————————————————————
P208C00
Measured voltage below limit
No Sub Type Information
No urea dosing
Wiring harness internal error in pump
Diagnostic Service 14. No additional action is needed
Check:
Wiring harness internal error in pump
Aftertreatment Reagent Pump Control Short
Circuit Low
————————————————————————————————————————————————————————————
P203A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
AdBlue tank level sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
AdBlue tank level sensor, Cables, Connectors
Reductant Level Sensor “A”
————————————————————————————————————————————————————————————
P108700
No Sub Type
Information
None
No fault
None
Diagnostic Service 14. No additional
action is needed
Check:
No fault
Injector 1 Missing Glitch
Signature
————————————————————————————————————————————————————————————
P107B00
No Sub Type
Information
.
Diagnostic Service 14. No additional
action is needed
.
Injector 2 Missing Glitch
Signature
————————————————————————————————————————————————————————————
P019700
Measured voltage below limit
No Sub Type Information
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Oil Temperature Short Circuit Low
————————————————————————————————————————————————————————————
P024313
Measured voltage outside the limits specified by the sensor
Circuit Open
Powerloss
Broken actuator or wire. Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Turbocharger/Supercharg er Wastegate Solenoid “A”
————————————————————————————————————————————————————————————
P024471
Actuator Stuck
Possible turbo damage
Wategate mechanically damaged
Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Wastegate Stuck Close
————————————————————————————————————————————————————————————
P024500
Measured voltage below limit
No Sub Type Information
Broken actuator, wire or ECM driver output Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Wastegate Short Circuit Low
————————————————————————————————————————————————————————————
P024600
Measured voltage above limit
No Sub Type Information
Powerloss
Broken actuator, wire or ECM driver output Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Wastegate Short Circuit High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P026200
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 1 Short Circuit High
————————————————————————————————————————————————————————————
P204300
No Sub Type Information
None
Urea tank temp sensor stuck high
Urea tank temp sensor
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor
Aftertreatment Reagent Tank Temperature Sensor Stuck
————————————————————————————————————————————————————————————
P209F73
Actuator Stuck Closed
None
Urea tank temp sensor or Urea tank heating system Urea tank temp sensor, Urea tank heating system
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor, Urea tank heating system
Aftertreatment Reagent Tank Temperature
————————————————————————————————————————————————————————————
P20F400
No Sub Type Information
Too low urea consumption
Urea level sensor stuck Clogged urea system Wrong urea tank Wrong dosing module Nozzle or
ACM Dosing module: dosing
valve
Diagnostic Service 14. No additional action is needed
Check:
Nozzle or
ACM Dosing module: dosing valve
AdBlue Consumption Too Low
————————————————————————————————————————————————————————————
P108900
No Sub Type
Information
.
Diagnostic Service 14. No additional
action is needed
.
Injector 3 Missing Glitch
Signature
————————————————————————————————————————————————————————————
P108B00
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Injector 4 Missing Glitch Signature
————————————————————————————————————————————————————————————
P108D00
No Sub Type
Information
.
Diagnostic Service 14. No additional
action is needed
.
Injector 5 Missing Glitch
Signature
————————————————————————————————————————————————————————————
P108F00
No Sub Type
Information
.
Diagnostic Service 14. No additional
action is needed
.
Injector 6 Missing Glitch
Signature
————————————————————————————————————————————————————————————
U029D00
Lost communication with the node
No Sub Type Information
MS from Nox-sensor ECU Nox-sensor power supply CAN communication between ECM and Nox-EUC
Diagnostic Service 14. No additional action is needed
Check:
Nox-sensor power supply
CAN communication between ECM and Nox-EUC
Lost Communication With NOx Sensor “A”
————————————————————————————————————————————————————————————
P204C00
Measured voltage below limit
No Sub Type Information
No urea dosing
ACM Pump module: AdBlue pressure sensor
ACM Pump module: Internal cabling
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Diagnostic Service 14. No additional action is needed
Check:
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Aftertreatment Reagent Pressure Sensor Circuit Low
————————————————————————————————————————————————————————————
U016700
No Sub Type Information
The engine can not be started
Immobilizer unit not installed. (When Immo in Cluster is used, the Cluster maybe did not wake up properly)
Immo system
Diagnostic Service 14. No additional action is needed
Check:
Immo system
Lost Communication With Vehicle Immobilizer Control Module
————————————————————————————————————————————————————————————
P220A1C
Circuit Voltage Out of Range
Too high voltage to NOx- sensor ECU
Battery voltage
Diagnostic Service 14. No additional action is needed
Check:
Battery voltage
NOx Sensor Supply Voltage Circuit (Bank 1 Sensor 1)
————————————————————————————————————————————————————————————
U042600
No Sub Type Information
The engine can not be started
ECM and Immobilizer(or Cluster) unit security codes do not match.
Immo system
Diagnostic Service 14. No additional action is needed
Check:
Immo system
Invalid Data Received From Vehicle Immobilizer Control Module
————————————————————————————————————————————————————————————
P114000
No Sub Type Information
No VCB
low engine oil temperature
.
Diagnostic Service 14. No additional action is needed
Check:
low engine oil temperature
Volvo Compression Brake (VCB) Control Oil Temperature Too Low
————————————————————————————————————————————————————————————
P113711
Measured voltage below limit
Circuit Short To Ground
Oil thermostat alwaysclosed.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Oil Thermostat
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P113712
Measured voltage above limit
Circuit Short To Battery
Oil thermostat always open. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Oil Thermostat
————————————————————————————————————————————————————————————
P113713
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil thermostat always open. Increased fuel consumption may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Oil Thermostat
————————————————————————————————————————————————————————————
P011164
Signal Plausibility Failure
None
The boost temperature sensor output is showing either too high or to low value.
(abnormal value) Harness
Sensor
Ambient air temperature sensor.
Diagnostic Service 14. No additional action is needed
Check:
Harness Sensor
Ambient air temperature sensor.
Intake Air Temperature Sensor 1 Circuit Range/Performance Bank 1
————————————————————————————————————————————————————————————
P20E892
Performance or Incorrect Operation
No urea dosing
ACM dosing module: Dosing valve leakage.
Bleed orifice leakage, pressure hose lekage, pump internal leakage, empty ureatank
Tank frozen.
if pump/tank-lines are mixed-up when connecting them to the pump unit there will be no pressure built (check color mar Empty Urea tank, Urea filter clogged, Urea inlet pipe leakage/blocked, Urea tank ventilation, ACM Pump module: Pump
Diagnostic Service 14. No additional action is needed
Check:
Empty Urea tank, Urea filter clogged, Urea inlet pipe leakage/blocked, Urea tank ventilation, ACM Pump module: Pump
Reductant Pressure Too Low
————————————————————————————————————————————————————————————
P21CA00
No Sub Type Information
No dozing
Voltage supply to ACM.
Voltage supply to Urea pump.
Diagnostic Service 14. No additional action is needed
Check:
Voltage supply to Urea pump.
Reductant Control Module Supply Voltage
————————————————————————————————————————————————————————————
P114411
Measured voltage
below limit
Circuit Short To Ground
EMS can not control starter
Start relay/harness
Diagnostic Service 14. No additional
action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P114412
Measured voltage above limit
Circuit Short To Battery
Impossible to activate starter motor.
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P114413
Measured voltage outside the limits specified by the
sensor
Circuit Open
Impossible to activate starter motor
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P116A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
No urea dosing
.
Diagnostic Service 14. No additional action is needed
.
Reductant Pump “A” Control Low Side
————————————————————————————————————————————————————————————
P116B00
Measured voltage below limit
No Sub Type Information
No urea dosing
.
Diagnostic Service 14. No additional action is needed
.
Reductant Pump “A”
Control Low Side Circuit Low
————————————————————————————————————————————————————————————
P116C00
Measured voltage above limit
No Sub Type Information
No urea dosing
.
Diagnostic Service 14. No additional action is needed
.
Reductant Pump “A” Control Low Side Circuit
High
————————————————————————————————————————————————————————————
P020A25
Signal Shape /
Waveform Failure
None
No fault
None
Diagnostic Service 14. No additional
action is needed
Check:
No fault
Cylinder 1 Injection
Timing
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P021900
No Sub Type Information
Engine speed is limited (to commonly 1200rpm). VCB and EPD activated to lower espd below deactivation limit (commonly 1000rpm).
Engine is/was overspeeding. Engine could be running on oil, due to e.g. faulty crankcase oil filter.
Diagnostic Service 14. No additional action is needed
Check:
Engine could be running on oil, due to e.g. faulty crankcase oil filter.
Engine Overspeed Condition
————————————————————————————————————————————————————————————
P115C00
Measured voltage above limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power Supply “C” Circuit High
————————————————————————————————————————————————————————————
P115D00
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power Supply “C” Circuit Low
————————————————————————————————————————————————————————————
P06E970
Actuator Stuck On
The starter motor is deactivated
The starter motor is deactivated due to that the cogwheels of the starter and engine are stuck
None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to that the cogwheels of the starter and engine are stuck
Engine Starter Performance
————————————————————————————————————————————————————————————
P06E998
Component or System Over Temperature
The starter motor is deactivated
The starter motor is deactivated due to overheat None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to overheat
Engine Starter Performance
————————————————————————————————————————————————————————————
P115E97
Component or System Operation Obstructed or Blocked
No dozing
Bleed orifice clogged
Bleed orifice, Urea pressure sensor,
Diagnostic Service 14. No additional action is needed
Check:
Bleed orifice, Urea pressure sensor,
Reductant Return No Flow Detected
————————————————————————————————————————————————————————————
P11609B
High/Excessive Flow
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Root Cause Unknown (First Level)
————————————————————————————————————————————————————————————
P116192
Performance or Incorrect Operation
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Insufficient Reagent Quality (First Level)
————————————————————————————————————————————————————————————
P116300
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – NOx Control Monitoring System (First Level)
————————————————————————————————————————————————————————————
P26047F
Measured voltage below limit
Actuator Stuck Off
Preheat relay problem or sense SC-.
Shorting wire may break when attempt
Preheat sense 1
Preheat relay
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1 Preheat relay
Intake Air Heater “A” Circuit Range/Performance
————————————————————————————————————————————————————————————
P115600
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power
Supply “A” Circuit High
————————————————————————————————————————————————————————————
P115700
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power
Supply “A” Circuit Low
————————————————————————————————————————————————————————————
P115800
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Reductant Control
Module Sensor Power Supply “B” Circuit High
————————————————————————————————————————————————————————————
P115900
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Reductant Control Module Sensor Power
Supply “B” Circuit Low
————————————————————————————————————————————————————————————
P115A00
No Sub Type Information
Possible incread risk of crystalization
Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
Exhaust Gas Temperature Sensor Circuit Signal Compare Failure Bank 1
Sensor 1
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P115B00
No Sub Type Information
None
The sensor is stuck Leakage in exhaust system Leakage in intake system Sensor
Diagnostic Service 14. No additional action is needed
Check:
Leakage in exhaust system Leakage in intake system Sensor
Exhaust Gas Temperature Sensor Circuit Stuck Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P116441
General Checksum Failure
All ACM functionality disabled, no urea dosing
No software in ACM
.
Diagnostic Service 14. No additional action is needed
Check:
No software in ACM
Reductant Control Module Internal Control Module Memory Checksum Error
————————————————————————————————————————————————————————————
P116500
No Sub Type Information
Buzzer signal (alert), Display of the message, with bip, simultaneously with the gear engaged pictogram.
Driver is at low speed but still shifts to high gear, range high.
Protective measure for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective measure for clutch/transmission
Driver Selected Too High Gear
————————————————————————————————————————————————————————————
P116600
No Sub Type Information
Buzzer signal (alert), Display of the message, with bip, simultaneously with the gear engaged pictogram.
Driver is at high speed but still down-shift to low gear, range low.
Protective measure for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective measure for clutch/transmission
Driver Selected Too Low Gear
————————————————————————————————————————————————————————————
P116700
No Sub Type Information
The starter motor is deactivated
The starter motor is deactivated due to that the PTO switch is active.
None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to that the PTO switch is active.
Starter Activated When PTO Is Active
————————————————————————————————————————————————————————————
P000041
General Checksum
Failure
The engine can not be
started
.
Diagnostic Service 14. No additional
action is needed
.
Control Module
————————————————————————————————————————————————————————————
P24FF00
No Sub Type Information
If tank temp is too high, no urea dosing
Urea tank temp is too high Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
Reductant Temperature Too High
————————————————————————————————————————————————————————————
U1FFF68
Event Information
None
None
Diagnostic Service 14. No additional action is needed
.
Factory Mode Active
————————————————————————————————————————————————————————————
P117A00
No Sub Type Information
Possible ammonia smell
SCR catalyst removed, Regent out of specification, Clogged dosing system Urea specification
Dosing system Catalyst deactivated
Diagnostic Service 14. No additional action is needed
Check:
Urea specification Dosing system Catalyst deactivated
SCR NOx Catalyst Efficiency Critically Below Threshold Bank 1
————————————————————————————————————————————————————————————
P047800
Measured voltage
above limit
No Sub Type
Information
Powerloss, engine break is
reduced
Broken actuator/Harness
AVU
Diagnostic Service 14. No additional
action is needed
Check:
AVU
Exhaust Pressure Control
Valve “A” High
————————————————————————————————————————————————————————————
P047700
Measured voltage
below limit
No Sub Type
Information
Powerloss, engine break is
reduced
Broken actuator/Harness
AVU
Diagnostic Service 14. No additional
action is needed
Check:
AVU
Exhaust Pressure Control
Valve “A” Low
————————————————————————————————————————————————————————————
P047513
Measured voltage outside the limits specified by the sensor
Circuit Open
Powerloss, engine break is reduced
Broken actuator/Harness AVU
Diagnostic Service 14. No additional action is needed
Check: AVU
Exhaust Pressure Control Valve “A”
————————————————————————————————————————————————————————————
P222764
Signal Plausibility Failure
Powerloss (minor) P3524:
Black smoke (minor)
The ambient air pressure is showing either too high or to low value.
(abnormal value) Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor ECM
Barometric Pressure Sensor “A” Circuit Range/Performance
————————————————————————————————————————————————————————————
P011513
Measured voltage outside the limits specified by the sensor
Circuit Open
Engine is difficult to start. Idle run regulation is detoriated.
Harness Sensor
Sensor/Harness
Diagnostic Service 14. No additional action is needed
Check: Sensor/Harness
Engine Coolant Temperature Sensor 1
————————————————————————————————————————————————————————————
P020D25
Signal Shape /
Waveform Failure
.
Diagnostic Service 14. No additional
action is needed
.
Cylinder 4 Injection
Timing
————————————————————————————————————————————————————————————
P020E25
Signal Shape /
Waveform Failure
.
Diagnostic Service 14. No additional
action is needed
.
Cylinder 5 Injection
Timing
————————————————————————————————————————————————————————————
P020F25
Signal Shape /
Waveform Failure
.
Diagnostic Service 14. No additional
action is needed
.
Cylinder 6 Injection
Timing
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P020B25
Signal Shape /
Waveform Failure
.
Diagnostic Service 14. No additional
action is needed
.
Cylinder 2 Injection
Timing
————————————————————————————————————————————————————————————
P020C25
Signal Shape / Waveform Failure
.
Diagnostic Service 14. No additional action is needed
.
Cylinder 3 Injection Timing
————————————————————————————————————————————————————————————
P205E1F
Circuit Intermittent
Urea tank temp sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor, Cables, Connectors
Reductant Tank Temperature Sensor Circuit
Intermittent/Erratic
————————————————————————————————————————————————————————————
P053E00
No Sub Type Information
Forced idle Engine shut down
The non-filtered pressure difference (between crankcase pressure and ambient air pressure) is/was above limit. (The fault code will remain during the entire driving cycle (unless reset).)
E.g. Blow-by at piston ring. NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Diagnostic Service 14. No additional action is needed
Check:
E.g. Blow-by at piston ring.
NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Crankcase Pressure Too High
————————————————————————————————————————————————————————————
P25AB00
Measured voltage above limit
No Sub Type Information
Possible black smoke during start.
Harness/Broken actuator Harness/Valve
Diagnostic Service 14. No additional action is needed
Check: Harness/Valve
Piston Cooling Oil Control Circuit High
————————————————————————————————————————————————————————————
P25AA00
Measured voltage below limit
No Sub Type Information
No piston cooling=>major engine damage if high
loads.
Harness/Broken actuator Harness/Valve
Diagnostic Service 14. No additional action is needed
Check: Harness/Valve
Piston Cooling Oil Control Circuit Low
————————————————————————————————————————————————————————————
P010513
Measured voltage outside the limits specified by the sensor
Circuit Open
Powerloss
Connectors. Harness. Sensor
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Manifold Absolute Pressure/Barometric Pressure Sensor
————————————————————————————————————————————————————————————
P010800
Measured voltage above limit
No Sub Type Information
Powerloss
Connectors. Harness. Sensor
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Manifold Absolute Pressure/Barometric Pressure Sensor Circuit High
————————————————————————————————————————————————————————————
P010662
Signal Compare Failure
Powerloss Black smoke
The boost pressure sensor output is showing either too high or to low value.
(abnormal value) Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance
————————————————————————————————————————————————————————————
P25AE00
No Sub Type
Information
.
Diagnostic Service 14. No additional
action is needed
.
Piston Cooling Oil
Pressure Too Low
————————————————————————————————————————————————————————————
P25A913
Measured voltage outside the limits specified by the
sensor
Circuit Open
Possible black smoke during start.
Harness/Broken actuator Harness/Valve
Diagnostic Service 14. No additional action is needed
Check: Harness/Valve
Piston Cooling Oil Control
————————————————————————————————————————————————————————————
P054070
Measured voltage above limit
Actuator Stuck On
Fuse for shorting wire breaks.
Sense wire SC+ or preheat relay broken
Preheat sense 1
Preheat relay
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1 Preheat relay
Intake Air Heater “A” Control
————————————————————————————————————————————————————————————
P225D00
No Sub Type Information
None except fault code and lamp
Sensor removed (measures surround air)
Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
NOx Sensor Performance – Signal Stuck Low Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P10F200
Measured voltage below limit
No Sub Type Information
None
Pressure switch / Harness Pressure switch/Harness
Diagnostic Service 14. No additional action is needed
Check:
Pressure switch/Harness
Air Filter Indicator Circuit Low
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P10F300
Measured voltage
above limit
No Sub Type
Information
None
Harness
Diagnostic Service 14. No additional
action is needed
Check:
Harness
Air Filter Indicator Circuit
High
————————————————————————————————————————————————————————————
P22FB00
No Sub Type Information
Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
NOx Sensor Performance – Sensing Element Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P110F90
Stuck On
Stop switch can not be activated
Switch
Engine stop switch
Diagnostic Service 14. No additional action is needed
Check:
Engine stop switch
Engine Stop Switch Stuck
————————————————————————————————————————————————————————————
P110400
No Sub Type Information
The engine can not be started
Bad software configuration Software download application
Diagnostic Service 14. No additional action is needed
Check:
Software download application
Factory Mode
————————————————————————————————————————————————————————————
P10F824
Signal Stuck High
.
Diagnostic Service 14. No additional action is needed
.
Air Filter Clogged
————————————————————————————————————————————————————————————
P055A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
.
Diagnostic Service 14. No additional action is needed
.
Engine Oil Pressure Sensor/Switch “B”
————————————————————————————————————————————————————————————
P055B64
Signal Plausibility Failure
The control function closes the PCJ valve. When the fault is set, the PCJ oil pressure is forced to max (if calibrated so in the pcj_ function).
The sensor is stuck, has an offset or another kind of rationality fault. It could also be the valve that cannot be closed.
Sensor/Valve
Diagnostic Service 14. No additional action is needed
Check: Sensor/Valve
Piston Cooling Oil Pressure Sensor Range/Performance
————————————————————————————————————————————————————————————
P055D00
Measured voltage above limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Piston Cooling Oil Pressure Sensor Circuit High
————————————————————————————————————————————————————————————
P112800
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Piston Cooling Oil Pressure Moderately Low
————————————————————————————————————————————————————————————
P029800
No Sub Type Information
Powerloss
Extreme driving conditions Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Engine Oil Over Temperature
————————————————————————————————————————————————————————————
P111600
No Sub Type Information
Intermittent Powerloss
VGT stuck, Wastegate stuck VGT Turbo, Wastegate
Diagnostic Service 14. No additional action is needed
Check:
VGT Turbo, Wastegate
Manifold Absolute Pressure Moderately Too
High
————————————————————————————————————————————————————————————
P111800
No Sub Type Information
Intermittent Powerloss
VGT stuck, Wastegate stuck VGT Turbo, Wastegate
Diagnostic Service 14. No additional action is needed
Check:
VGT Turbo, Wastegate
Manifold Absolute Pressure Too High
————————————————————————————————————————————————————————————
P111D00
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Engine Coolant Level Moderately Low
————————————————————————————————————————————————————————————
P111E00
No Sub Type Information
Powerloss
Extreme Driving conditions
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Engine Coolant Temperature Moderately High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P112500
No Sub Type Information
Powerloss
Extreme driving conditions Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Engine Oil Temperature Moderately High
————————————————————————————————————————————————————————————
U117888
It has not been possible to send frames on Vehicle Communication Powertrain CAN and It has not been possible to receive frames on Vehicle Communication Powertrain CAN
Bus off
.
Diagnostic Service 14. No additional action is needed
.
Vehicle Communication Powertrain CAN
————————————————————————————————————————————————————————————
P253913
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Low Pressure Fuel System Sensor Circuit
————————————————————————————————————————————————————————————
P254200
Measured voltage above limit
No Sub Type Information
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check:
Harness Sensor
Low Pressure Fuel System Sensor Circuit High
————————————————————————————————————————————————————————————
P008A00
No Sub Type Information
Fuel injection can be affected.
High differential pressure over filter.
Leakage Filter
Sensor
Diagnostic Service 14. No additional action is needed
Check: Filter Sensor
Low Pressure Fuel System Pressure – Too Low
————————————————————————————————————————————————————————————
P113500
No Sub Type Information
Engine speed is limited (to commonly 1200rpm). VCB and EPG activated to lower espd below deactivation limit (commonly 1000rpm).
The non-filtered pressure difference (between crankcase pressure and ambient air pressure) is/was above limit. (The fault code will remain during the entire driving cycle (unless reset).)
E.g. Blow-by at piston ring. NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Diagnostic Service 14. No additional action is needed
Check:
E.g. Blow-by at piston ring.
NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Crankcase Pressure Relative To Ambient Pressure Too High
————————————————————————————————————————————————————————————
U000188
It has not been possible to send frames on High Speed CAN Communication Bus and It has not been possible to receive frames on High Speed CAN Communication Bus
Bus off
.
Diagnostic Service 14. No additional action is needed
.
CAN Communication Backbone 2 Net
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U001088
It has not been possible to send frames on Medium Speed CAN Communication Bus and It has not been possible to receive frames on Medium Speed CAN Communication Bus
Bus off
.
Diagnostic Service 14. No additional action is needed
.
CAN Communication Backbone 1 Net
————————————————————————————————————————————————————————————
U010187
Missing Message
ETC2 not responding
.
Diagnostic Service 14. No additional
action is needed
Check:
ETC2 not responding
Lost Communication with
TECU
————————————————————————————————————————————————————————————
P034031
No Signal
The engine start time will increase.
Possible loss of power
Sensor/Harness Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Camshaft Position Sensor “A” Bank 1 or Single Sensor
————————————————————————————————————————————————————————————
P034138
Signal Frequency Incorrect
The engine start time will increase.
Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Camshaft Position Sensor A Circuit Range/Performance
————————————————————————————————————————————————————————————
P052612
Measured voltage above limit
Circuit Short To Battery
Either
1. Fan will work as on/off fan. 100% fan speed if cooling is needed. Higher fuel consumption.
Or
2. Fan will work in open loop mode. Deteriorated fan control, but might not be noticable to driver.
Broken sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Fan Speed Sensor Circuit
————————————————————————————————————————————————————————————
P054300
Measured voltage outside the limits specified by the
sensor
No Sub Type Information
Might get start problems in cold climate.
Heating element or wire broken.
Preheat sense 1
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1
Intake Air Heater A Circuit Open
————————————————————————————————————————————————————————————
P054415
Measured voltage outside the limits specified by the
sensor
Circuit Short To Battery or Open
Fault code set by ACM: IDTC_ENGEXHTEMP_OC
Diagnostic Service 14. No additional action is needed
Check:
Fault code set by ACM: IDTC_ENGEXHTEMP_OC
Exhaust Gas Temperature Sensor Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P001676
Wrong Mounting Position
Fuel consumption increased
Bad correlation between cam and crank, engine transmission not correct
Engine transmission
Diagnostic Service 14. No additional action is needed
Check:
Engine transmission
Crankshaft Position – Camshaft Position Correlation
————————————————————————————————————————————————————————————
P007100
No Sub Type Information
Ambient air temp sensor or boost temp sensor faulty Ambient air temp sensor or Boost temp sensor
Diagnostic Service 14. No additional action is needed
Check:
Ambient air temp sensor or Boost temp sensor
Ambient Air Temperature Sensor Range/Performance
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P02CD00
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 1 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02CF00
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 2 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D100
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 3 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D300
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 4 Fuel Injector Offset Learning at Max Limit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P02D500
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 5 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D700
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 6 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P033531
No Signal
Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running. Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankshaft Position Sensor “A”
————————————————————————————————————————————————————————————
P033638
Signal Frequency Incorrect
Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running. Possible loss of power
Sensor monting Sensor/Lack of shims
Diagnostic Service 14. No additional action is needed
Check:
Sensor/Lack of shims
Crankshaft Position Sensor A Circuit Range/Performance
————————————————————————————————————————————————————————————
P033900
No Sub Type Information
The engine start time will increase.Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running.
Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankshaft Position Sensor A Circuit Intermittent
————————————————————————————————————————————————————————————
P203F00
No Sub Type Information
No urea dosing
Urea symbol in cluster
Tank almost empty, stop dosing to maintain cooling ECM interpretation of raw value. Urea level. DST problem.
Diagnostic Service 14. No additional action is needed
Check:
ECM interpretation of raw value. Urea level. DST problem.
Reductant Level Low
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P205A13
Measured voltage outside the limits specified by the sensor
Circuit Open
None
AdBlue tank temp sensor Cables
Connectors
Urea tank temp sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor, Cables, Connectors
Reductant Tank Temperature Sensor
————————————————————————————————————————————————————————————
P208064
Signal Plausibility Failure
None
The sensor is not plausible Leakage in exhaust system Leakage in intake system Sensor
Diagnostic Service 14. No additional action is needed
Check:
Leakage in exhaust system Leakage in intake system Sensor
Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P220013
Measured voltage outside the limits specified by the sensor
Circuit Open
Cabling between Nox- sensor and Nox-sensor ECU Nox-sensor
Nox-sensor cabling Nox-sensor
Diagnostic Service 14. No additional action is needed
Check:
Nox-sensor cabling Nox-sensor
NOx Sensor Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P220164
Signal Plausibility Failure
Excessive urea dosing (only for SCR system)
Exhaust system leakage Air intake leakage
Nox-sensor
Dosing system (only for SCR system)
Exhaust system Air intake system
Nox-sensor
Diagnostic Service 14. No additional action is needed
Check:
Dosing system (only for SCR system) Exhaust system
Air intake system Nox-sensor
NOx Sensor Circuit Range/Performance
————————————————————————————————————————————————————————————
P060100
No Sub Type Information
Engine derate
signature failure
.
Diagnostic Service 14. No additional action is needed
Check: signature failure
Internal Control Module Memory Check Sum Error
————————————————————————————————————————————————————————————
P060700
No Sub Type
Information
Not possible to reprogram
ECU
.
Diagnostic Service 14. No additional
action is needed
.
Control Module
Performance
————————————————————————————————————————————————————————————
P06151C
Measured voltage outside the limits specified by the
sensor
Circuit Voltage Out of Range
Impossible to activate starter motor
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay
————————————————————————————————————————————————————————————
P061600
Measured voltage
below limit
No Sub Type
Information
EMS can not control starter
Start relay/harness
Diagnostic Service 14. No additional
action is needed
Check:
Start relay/Harness
Starter Relay Circuit Low
————————————————————————————————————————————————————————————
P061700
Measured voltage
above limit
No Sub Type
Information
Impossible to activate
starter motor.
Start relay/harness
Diagnostic Service 14. No additional
action is needed
Check:
Start relay/Harness
Starter Relay Circuit High
————————————————————————————————————————————————————————————
P066800
Measured voltage below limit
No Sub Type Information
None
Internal fault in ECM ECM
Diagnostic Service 14. No additional action is needed
Check: ECM
PCM/ECM/TCM Internal Temperature Sensor Circuit Low
————————————————————————————————————————————————————————————
P06B100
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply A Circuit Low
————————————————————————————————————————————————————————————
P06B200
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply A Circuit High
————————————————————————————————————————————————————————————
P06B400
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply B Circuit Low
————————————————————————————————————————————————————————————
P06B500
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply B Circuit High
————————————————————————————————————————————————————————————
P20EE00
No Sub Type Information
NOx-conversion reduced by appr. 50%
Possible ammonia smell
Regent out of specification, Dosing performance low Urea specification
Dosing system
Diagnostic Service 14. No additional action is needed
Check:
Urea specification Dosing system
SCR NOx Catalyst Efficiency Below Threshold (Bank 1)
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P260013
Measured voltage outside the limits specified by the
sensor
Circuit Open
Pump always at half speed. High coolant temperatures may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Coolant Pump Control Circuit/Open
————————————————————————————————————————————————————————————
P260200
Measured voltage below limit
No Sub Type Information
Pump always runs at full speed. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Coolant Pump Control Circuit Low
————————————————————————————————————————————————————————————
P260300
Measured voltage above limit
No Sub Type Information
Pump always at half speed. High coolant temperatures may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Coolant Pump Control Circuit High
————————————————————————————————————————————————————————————
P261087
Missing Message
Timestamps from Cluster not available
J1708 time data failure and J1939 message does not exist. (Cluster error).
Cluster
Diagnostic Service 14. No additional action is needed
Check: Cluster
ECM/PCM Internal Engine Off Timer Performance
————————————————————————————————————————————————————————————
P2BA700
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Empty Reagent Tank
————————————————————————————————————————————————————————————
P023400
No Sub Type Information
Too high pressure Turbine , Compressor
Diagnostic Service 14. No additional action is needed
Check:
Turbine , Compressor
Turbocharger/Supercharg er Overboost Condition
————————————————————————————————————————————————————————————
P029900
No Sub Type Information
Too low pressure
Boost leakage, wastegate, VGT, compressor.
Diagnostic Service 14. No additional action is needed
Check:
Boost leakage, wastegate, VGT, compressor.
Turbocharger/Supercharg er Underboost
————————————————————————————————————————————————————————————
U300001
Measured voltage outside the limits specified by the
sensor
General Electrical Failure
Possible damage on EMS system components depending on the high
voltage (>36V)
Generator, external charger
Diagnostic Service 14. No additional action is needed
Check:
Generator, external charger
Electronic control unit
————————————————————————————————————————————————————————————
U300041
Program memory corruption
General Checksum Failure
The engine can not be started
No software Software download
application
Diagnostic Service 14. No additional action is needed
Check:
Software download application
Electronic control unit
————————————————————————————————————————————————————————————
P007087
Missing Message
None
J1708 and CAN ambient air temperature message does not exist.
Harness. Cluster
Diagnostic Service 14. No additional action is needed
Check:
Harness. Cluster
Ambient Air Temperature Sensor “A”
————————————————————————————————————————————————————————————
P011013
Measured voltage outside the limits specified by the sensor
Circuit Open
Engine is running but could be difficult to start in cold climate.
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Intake Air Temperature Sensor 1 Bank 1
————————————————————————————————————————————————————————————
P011200
Measured voltage below limit
No Sub Type Information
Engine is running but could be difficult to start in cold climate.
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Intake Air Temperature Sensor 1 Circuit Low Bank 1
————————————————————————————————————————————————————————————
P011700
Measured voltage below limit
No Sub Type Information
Engine is difficult to start.
Idle run regulation is detoriated.
Harness Sensor
Sensor/Harness
Diagnostic Service 14. No additional action is needed
Check: Sensor/Harness
Engine Coolant Temperature Circuit Low
————————————————————————————————————————————————————————————
P021700
No Sub Type Information
Powerloss
Extreme Driving conditions Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Engine Coolant Over Temperature Condition
————————————————————————————————————————————————————————————
P048013
Measured voltage outside the limits specified by the
sensor
Circuit Open
Fan runs at full speed. Increased fuel consumption may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P051B64
Signal Plausibility Failure
Powerloss (minor) P3524:
Black smoke (minor)
The crank case pressure is showing either too high or to low value.
(abnormal value) Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor ECM
Engine High Resolution Crankcase Pressure Circuit Range/Performance
————————————————————————————————————————————————————————————
P051A13
Measured voltage outside the limits specified by the sensor
Circuit Open
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankcase Pressure Sensor
————————————————————————————————————————————————————————————
P051D00
Measured voltage above limit
No Sub Type Information
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Engine High Resolution Crankcase Pressure
————————————————————————————————————————————————————————————
P052300
Measured voltage above limit
No Sub Type Information
Oil pressure shows 0 in the cluster. Engine is running.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Engine Oil Pressure Circuit High
————————————————————————————————————————————————————————————
P052400
No Sub Type Information
Low pressure, powerloss
Oil leakage, broken oil pump, clogged oil system Oil system
Diagnostic Service 14. No additional action is needed
Check:
Oil system
Engine Oil Pressure Too Low
————————————————————————————————————————————————————————————
P222800
Measured voltage below limit
No Sub Type Information
None
Internal fault in ECM Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor
ECM
Barometric Pressure Circuit Low
————————————————————————————————————————————————————————————
P222900
Measured voltage above limit
No Sub Type Information
None
Internal fault in ECM Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check:
Sensor ECM
Barometric Pressure Circuit High
————————————————————————————————————————————————————————————
P226400
No Sub Type Information
None
No error: Used for indication
when priming pump is active
None
Diagnostic Service 14. No additional action is needed
Check:
No error: Used for indication when priming pump is active
Water in Fuel Sensor
————————————————————————————————————————————————————————————
P226600
Measured voltage
below limit
No Sub Type
Information
Will give water in fuel
indication.
Harness
Diagnostic Service 14. No additional
action is needed
Check:
Harness
Water In Fuel Indicator
Circuit Low
————————————————————————————————————————————————————————————
P226700
Measured voltage above limit
No Sub Type Information
Undetected water in fuel can lead to engine stop
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Water In Fuel Indicator Circuit High
————————————————————————————————————————————————————————————
P250C00
Measured voltage below limit
No Sub Type Information
Oil level can not be measured.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check:
Harness Sensor
Engine Oil Level Circuit Low
————————————————————————————————————————————————————————————
P250F00
No Sub Type Information
None
Critically low oil level Leakage
Leakage
Sensor
Diagnostic Service 14. No additional action is needed
Check: Leakage Sensor
Engine Oil Level Too Low
————————————————————————————————————————————————————————————
P255613
Measured voltage outside the limits specified by the
sensor
Circuit Open
Coolant level can not be detected.
Harness Harness connector
sensor
Diagnostic Service 14. No additional action is needed
Check: Harness connector
sensor
Engine Coolant Level Sensor/Switch
————————————————————————————————————————————————————————————
P255900
Measured voltage above limit
No Sub Type Information
Coolant level can not be detected.
Harness Harness connector
sensor
Diagnostic Service 14. No additional action is needed
Check: Harness connector
sensor
Engine Coolant Level Circuit High
————————————————————————————————————————————————————————————
P256000
No Sub Type Information
Powerloss
Coolant level below range if not Harness
Coolant system
Diagnostic Service 14. No additional action is needed
Check:
Coolant system
Engine Coolant Level Low
————————————————————————————————————————————————————————————
P108600
No Sub Type Information
None
Low oil level Leakage Leakage
Sensor
Diagnostic Service 14. No additional action is needed
Check: Leakage Sensor
Oil Level Moderately Low
————————————————————————————————————————————————————————————
P20BF00
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Reagent Hose Heater 2 Short Circuit Low
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U014100
Lost communication with the node on Medium Speed CAN Communication Bus
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With VMCU
————————————————————————————————————————————————————————————
U012A87
Lost communication with the node
Missing Message
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With CCIOM
————————————————————————————————————————————————————————————
P109000
No Sub Type Information
Display of the message, without bip, simultaneously with the gear engaged
pictogram
Driver started at too high gear at start
Protective alert for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective alert for clutch/transmission
Transmission High Gear At Start
————————————————————————————————————————————————————————————
P208E00
No Sub Type Information
No urea dosing
Sensor/Harness dosing valve
injector, clogged hoses
Diagnostic Service 14. No additional action is needed
Check:
dosing valve
injector, clogged hoses
Aftertreatment Reagent Dosing Valve Clogged
————————————————————————————————————————————————————————————
P109541
General Checksum
Failure
Engine derate
.
Diagnostic Service 14. No additional
action is needed
.
Aftertreatment Control
Unit
————————————————————————————————————————————————————————————
P109641
General Checksum
Failure
Engine derate
.
Diagnostic Service 14. No additional
action is needed
.
Transmission Control Unit
————————————————————————————————————————————————————————————
P069200
Measured voltage above limit
No Sub Type Information
Fan runs at full speed. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit High
————————————————————————————————————————————————————————————
P069100
Measured voltage below limit
No Sub Type Information
Fan always deactivated or always activated if fault is intermittent.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit Low
————————————————————————————————————————————————————————————
U015500
Lost communication with the node on Medium Speed CAN Communication Bus
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With Instrument Panel Cluster (IPC) Control Module
————————————————————————————————————————————————————————————
P052013
Measured voltage outside the limits specified by the sensor
Circuit Open
Oil pressure shows 0 in the cluster. Engine is running.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Pressure Sensor/Switch “A”
————————————————————————————————————————————————————————————
P066613
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Internal fault in ECM ECM
Diagnostic Service 14. No additional action is needed
Check: ECM
Control Module Internal Temperature Sensor “A”
————————————————————————————————————————————————————————————
P020113
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 1 Injector “A”
————————————————————————————————————————————————————————————
P020313
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 3 Injector “A”
————————————————————————————————————————————————————————————
P020413
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 4 Injector “A”
————————————————————————————————————————————————————————————
P020513
Measured voltage outside the limits specified by the sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 5 Injector “A”
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P020613
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 6 Injector “A”
————————————————————————————————————————————————————————————
P220E93
No Operation
Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
NOx Sensor Heater Control Circuit Range/Performance (Bank
1 Sensor 1)
————————————————————————————————————————————————————————————
P250A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil level can not be measured.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Level Sensor
————————————————————————————————————————————————————————————
P020213
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 2 Injector “A”
————————————————————————————————————————————————————————————
P100E18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 2
————————————————————————————————————————————————————————————
P100F18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 3
————————————————————————————————————————————————————————————
P101018
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 4
————————————————————————————————————————————————————————————
P101518
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 5
————————————————————————————————————————————————————————————
P101618
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 6
————————————————————————————————————————————————————————————
P101711
Measured voltage below limit
Circuit Short To Ground
High fuel consumption due to fuel leakage.
Broken solenoid, wire or ECM driver output
Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P101712
Measured voltage above limit
Circuit Short To Battery
Valve constantly shut.
Broken solenoid, wire or ECM driver output
Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P101713
Measured voltage outside the limits specified by the sensor
Circuit Open
Valve constantly shut.
Broken solenoid or wire. Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P220300
No Sub Type Information
Cabling between Nox- sensor and Nox-sensor ECU Nox-sensor
Nox-sensor cabling Nox-sensor
Diagnostic Service 14. No additional action is needed
Check:
Nox-sensor cabling Nox-sensor
NOx Sensor Circuit High Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P2BA800
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Interruption of Reagent Dosing Activity
————————————————————————————————————————————————————————————
P2BA900
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Insufficient Reagent Quality
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P2BAA00
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Low Reagent Consumption
————————————————————————————————————————————————————————————
P2BAD00
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Root Cause Unknown
————————————————————————————————————————————————————————————
P2BAE96
Component Internal Failure
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – NOx Control Monitoring System
————————————————————————————————————————————————————————————
P100211
Measured voltage below limit
Circuit Short To Ground
Induction air is hot. Preheat relay is impossible to turn
off.
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Preheat Relay
————————————————————————————————————————————————————————————
P100212
Measured voltage above limit
Circuit Short To Battery
Preheat relay not activated. White smoke for cold start. Start problems in cold climate.
Preheat relay solenoid shorted
Preheat relay.
Diagnostic Service 14. No additional action is needed
Check: Preheat relay.
Preheat Relay
————————————————————————————————————————————————————————————
P100213
Measured voltage outside the limits specified by the sensor
Circuit Open
Preheat relay not activated. White smoke for cold start. Start problems in cold climate.
Harness or Preheat relay solenoid
Harness. Preheat relay.
Diagnostic Service 14. No additional action is needed
Check:
Harness. Preheat relay.
Preheat Relay
————————————————————————————————————————————————————————————
P100629
Signal invalid
None
The boost temperature sensor output is showing constant value.
Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Intake Air Temperature Sensor 1 Stuck Bank 1
————————————————————————————————————————————————————————————
P100713
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Pressure switch / Harness Pressure switch/Harness
Diagnostic Service 14. No additional action is needed
Check:
Pressure switch/Harness
Air Filter Indicator
————————————————————————————————————————————————————————————
P100D18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 1
————————————————————————————————————————————————————————————
P102111
Measured voltage below limit
Circuit Short To Ground
VCB can not be turned off. Causes engine to stop.
Engine impossible to
restart.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
P102112
Measured voltage above limit
Circuit Short To Battery
VCB can not be turned on. Engine break function derated. Gear shift performance derated for some automatic transmission boxes.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
P102113
Measured voltage outside the limits specified by the sensor
Circuit Open
VCB can not be turned on. Engine break function derated. Gear shift performance derated for some automatic transmission boxes.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
U010E00
Lost communication with the node
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With Reductant Control
Module
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P019513
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Temperature Sensor “A”
————————————————————————————————————————————————————————————
P204A13
Measured voltage outside the limits specified by the sensor
Circuit Open
No urea dosing
ACM Pump module: AdBlue pressure sensor
ACM Pump module: Internal cabling
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Diagnostic Service 14. No additional action is needed
Check:
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Reductant Pressure Sensor
————————————————————————————————————————————————————————————
P203D00
Measured voltage above limit
No Sub Type Information
None
AdBlue tank level sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
AdBlue tank level sensor, Cables, Connectors
Aftertreatment Reagent Level Short Circuit High
————————————————————————————————————————————————————————————
P208A13
Measured voltage outside the limits specified by the sensor
Circuit Open
No urea dosing
Wiring harness internal error in pump
Diagnostic Service 14. No additional action is needed
Check:
Wiring harness internal error in pump
Reductant Pump “A” Control
————————————————————————————————————————————————————————————
P026500
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 2 Short Circuit High
————————————————————————————————————————————————————————————
P026800
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 3 Short Circuit High
————————————————————————————————————————————————————————————
P027100
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 4 Short Circuit High
————————————————————————————————————————————————————————————
P027400
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 5 Short Circuit High
————————————————————————————————————————————————————————————
P027700
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 6 Short Circuit High
————————————————————————————————————————————————————————————
P054500
Measured voltage below limit
No Sub Type Information
Fault code set by ACM: IDTC_ENGEXHTEMP_SCL
Diagnostic Service 14. No additional action is needed
Check:
Fault code set by ACM: IDTC_ENGEXHTEMP_SCL
Exhaust Gas Temperature Short Circuit Low
————————————————————————————————————————————————————————————
P20B300
Measured voltage below limit
No Sub Type Information
None
.
Diagnostic Service 14. No additional action is needed
.
Reductant Heater Coolant Control Valve Circuit Low
————————————————————————————————————————————————————————————
P204800
Measured voltage below limit
No Sub Type Information
No urea dosing
ACM Pump module: DCU ACM Pump module: internal cabling
ACM Pump module: DCU,
ACM Pump module: internal cabling
Diagnostic Service 14. No additional action is needed
Check:
ACM Pump module: DCU, ACM Pump module: internal cabling
Aftertreatment Reagent Dosing Valve Short Circuit Low
————————————————————————————————————————————————————————————
P204713
Measured voltage outside the limits specified by the sensor
Circuit Open
no urea dosing
Cable / Connectors
ACM Dosing module: Dosing valve
Cable / Connectors ACM Dosing module: Dosing
valve
Diagnostic Service 14. No additional action is needed
Check:
Cable / Connectors ACM Dosing module: Dosing valve
Reductant Injection Valve Control Bank 1 Unit 1
————————————————————————————————————————————————————————————
P20C300
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Reagent Hose Heater 3 Short
Circuit Low
————————————————————————————————————————————————————————————
P20BB00
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Reagent Hose Heater 1 Short
Circuit Low
————————————————————————————————————————————————————————————
P20A200
Measured voltage below limit
No Sub Type Information
Not possible to perform afterrun
Internal electrical failure in valve within the ACM
Diagnostic Service 14. No additional action is needed
Check:
Internal electrical failure in valve within the ACM
Aftertreatment Reagent Direction Valve Short
Circuit Low
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P065900
Measured voltage above limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
ACM Actuator High Supply 1 Short Circuit
High
————————————————————————————————————————————————————————————
P065800
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
ACM Actuator High Supply 1 Short Circuit Low
————————————————————————————————————————————————————————————
P208D00
Measured voltage above limit
No Sub Type Information
No urea dosing
Wiring harness internal error in pump
Diagnostic Service 14. No additional action is needed
Check:
Wiring harness internal error in pump
Aftertreatment Reagent
Pump Control Short Circut High
————————————————————————————————————————————————————————————
P208C00
Measured voltage below limit
No Sub Type Information
No urea dosing
Wiring harness internal error in pump
Diagnostic Service 14. No additional action is needed
Check:
Wiring harness internal error in pump
Aftertreatment Reagent Pump Control Short
Circuit Low
————————————————————————————————————————————————————————————
P203A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
AdBlue tank level sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
AdBlue tank level sensor, Cables, Connectors
Reductant Level Sensor “A”
————————————————————————————————————————————————————————————
P108700
No Sub Type
Information
None
No fault
None
Diagnostic Service 14. No additional
action is needed
Check:
No fault
Injector 1 Missing Glitch
Signature
————————————————————————————————————————————————————————————
P107B00
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Injector 2 Missing Glitch Signature
————————————————————————————————————————————————————————————
P019700
Measured voltage below limit
No Sub Type Information
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check:
Harness Sensor
Oil Temperature Short Circuit Low
————————————————————————————————————————————————————————————
P024313
Measured voltage outside the limits specified by the
sensor
Circuit Open
Powerloss
Broken actuator or wire. Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Turbocharger/Supercharg er Wastegate Solenoid “A”
————————————————————————————————————————————————————————————
P024471
Actuator Stuck
Possible turbo damage
Wategate mechanically damaged
Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Wastegate Stuck Close
————————————————————————————————————————————————————————————
P024500
Measured voltage below limit
No Sub Type Information
Broken actuator, wire or ECM driver output
Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Wastegate Short Circuit Low
————————————————————————————————————————————————————————————
P024600
Measured voltage above limit
No Sub Type Information
Powerloss
Broken actuator, wire or ECM driver output
Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Wastegate Short Circuit High
————————————————————————————————————————————————————————————
P026200
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 1 Short Circuit High
————————————————————————————————————————————————————————————
P204300
No Sub Type Information
None
Urea tank temp sensor stuck high
Urea tank temp sensor
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor
Aftertreatment Reagent Tank Temperature Sensor Stuck
————————————————————————————————————————————————————————————
P209F73
Actuator Stuck Closed
None
Urea tank temp sensor or Urea tank heating system Urea tank temp sensor, Urea tank heating system
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor, Urea tank heating system
Aftertreatment Reagent Tank Temperature
————————————————————————————————————————————————————————————
P20F400
No Sub Type Information
Too low urea consumption
Urea level sensor stuck Clogged urea system Wrong urea tank Wrong dosing module Nozzle or
ACM Dosing module: dosing
valve
Diagnostic Service 14. No additional action is needed
Check:
Nozzle or
ACM Dosing module: dosing valve
AdBlue Consumption Too Low
————————————————————————————————————————————————————————————
P108900
No Sub Type
Information
.
Diagnostic Service 14. No additional
action is needed
.
Injector 3 Missing Glitch
Signature
————————————————————————————————————————————————————————————
P108B00
No Sub Type
Information
.
Diagnostic Service 14. No additional
action is needed
.
Injector 4 Missing Glitch
Signature
————————————————————————————————————————————————————————————
P108D00
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Injector 5 Missing Glitch Signature
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P108F00
No Sub Type
Information
.
Diagnostic Service 14. No additional
action is needed
.
Injector 6 Missing Glitch
Signature
————————————————————————————————————————————————————————————
U029D00
Lost communication with the node
No Sub Type Information
MS from Nox-sensor ECU Nox-sensor power supply CAN communication between ECM and Nox-EUC
Diagnostic Service 14. No additional action is needed
Check:
Nox-sensor power supply
CAN communication between ECM and Nox-EUC
Lost Communication With NOx Sensor “A”
————————————————————————————————————————————————————————————
P204C00
Measured voltage below limit
No Sub Type Information
No urea dosing
ACM Pump module: AdBlue pressure sensor
ACM Pump module: Internal cabling
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Diagnostic Service 14. No additional action is needed
Check:
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Aftertreatment Reagent Pressure Sensor Circuit Low
————————————————————————————————————————————————————————————
U016700
No Sub Type Information
The engine can not be started
Immobilizer unit not installed. (When Immo in Cluster is used, the Cluster maybe did not wake up properly)
Immo system
Diagnostic Service 14. No additional action is needed
Check:
Immo system
Lost Communication With Vehicle Immobilizer Control Module
————————————————————————————————————————————————————————————
P220A1C
Circuit Voltage Out of Range
Too high voltage to NOx- sensor ECU
Battery voltage
Diagnostic Service 14. No additional action is needed
Check:
Battery voltage
NOx Sensor Supply Voltage Circuit (Bank 1 Sensor 1)
————————————————————————————————————————————————————————————
U042600
No Sub Type Information
The engine can not be started
ECM and Immobilizer(or Cluster) unit security codes do not match.
Immo system
Diagnostic Service 14. No additional action is needed
Check:
Immo system
Invalid Data Received From Vehicle Immobilizer Control Module
————————————————————————————————————————————————————————————
P114000
No Sub Type Information
No VCB
low engine oil temperature
.
Diagnostic Service 14. No additional action is needed
Check:
low engine oil temperature
Volvo Compression Brake (VCB) Control Oil Temperature Too Low
————————————————————————————————————————————————————————————
P113711
Measured voltage below limit
Circuit Short To Ground
Oil thermostat alwaysclosed.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Oil Thermostat
————————————————————————————————————————————————————————————
P113712
Measured voltage above limit
Circuit Short To Battery
Oil thermostat always open. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Oil Thermostat
————————————————————————————————————————————————————————————
P113713
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil thermostat always open. Increased fuel consumption may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Oil Thermostat
————————————————————————————————————————————————————————————
P011164
Signal Plausibility Failure
None
The boost temperature sensor output is showing either too high or to low value.
(abnormal value) Harness
Sensor
Ambient air temperature sensor.
Diagnostic Service 14. No additional action is needed
Check:
Harness Sensor
Ambient air temperature sensor.
Intake Air Temperature Sensor 1 Circuit Range/Performance Bank 1
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P20E892
Performance or Incorrect Operation
No urea dosing
ACM dosing module: Dosing valve leakage.
Bleed orifice leakage, pressure hose lekage, pump internal leakage, empty ureatank
Tank frozen.
if pump/tank-lines are mixed-up when connecting them to the pump unit there will be no pressure built (check color mar Empty Urea tank, Urea filter clogged, Urea inlet pipe leakage/blocked, Urea tank ventilation, ACM Pump module: Pump
Diagnostic Service 14. No additional action is needed
Check:
Empty Urea tank, Urea filter clogged, Urea inlet pipe leakage/blocked, Urea tank ventilation, ACM Pump module: Pump
Reductant Pressure Too Low
————————————————————————————————————————————————————————————
P21CA00
No Sub Type Information
No dozing
Voltage supply to ACM.
Voltage supply to Urea pump.
Diagnostic Service 14. No additional action is needed
Check:
Voltage supply to Urea pump.
Reductant Control Module Supply Voltage
————————————————————————————————————————————————————————————
P114411
Measured voltage below limit
Circuit Short To Ground
EMS can not control starter
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P114412
Measured voltage
above limit
Circuit Short To Battery
Impossible to activate
starter motor.
Start relay/harness
Diagnostic Service 14. No additional
action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P114413
Measured voltage outside the limits specified by the
sensor
Circuit Open
Impossible to activate starter motor
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P116A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
No urea dosing
.
Diagnostic Service 14. No additional action is needed
.
Reductant Pump “A” Control Low Side
————————————————————————————————————————————————————————————
P116B00
Measured voltage below limit
No Sub Type Information
No urea dosing
.
Diagnostic Service 14. No additional action is needed
.
Reductant Pump “A” Control Low Side Circuit
Low
————————————————————————————————————————————————————————————
P116C00
Measured voltage above limit
No Sub Type Information
No urea dosing
.
Diagnostic Service 14. No additional action is needed
.
Reductant Pump “A” Control Low Side Circuit
High
————————————————————————————————————————————————————————————
P020A25
Signal Shape /
Waveform Failure
None
No fault
None
Diagnostic Service 14. No additional
action is needed
Check:
No fault
Cylinder 1 Injection
Timing
————————————————————————————————————————————————————————————
P021900
No Sub Type Information
Engine speed is limited (to commonly 1200rpm). VCB and EPD activated to lower espd below deactivation limit (commonly 1000rpm).
Engine is/was overspeeding. Engine could be running on oil, due to e.g. faulty crankcase oil filter.
Diagnostic Service 14. No additional action is needed
Check:
Engine could be running on oil, due to e.g. faulty crankcase oil filter.
Engine Overspeed Condition
————————————————————————————————————————————————————————————
P115C00
Measured voltage above limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power Supply “C” Circuit High
————————————————————————————————————————————————————————————
P115D00
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power Supply “C” Circuit Low
————————————————————————————————————————————————————————————
P06E970
Actuator Stuck On
The starter motor is deactivated
The starter motor is deactivated due to that the cogwheels of the starter and engine are stuck
None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to that the cogwheels of the starter and engine are stuck
Engine Starter Performance
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P06E998
Component or System Over Temperature
The starter motor is deactivated
The starter motor is deactivated due to overheat None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to overheat
Engine Starter Performance
————————————————————————————————————————————————————————————
P115E97
Component or System Operation Obstructed or Blocked
No dozing
Bleed orifice clogged
Bleed orifice, Urea pressure sensor,
Diagnostic Service 14. No additional action is needed
Check:
Bleed orifice, Urea pressure sensor,
Reductant Return No Flow Detected
————————————————————————————————————————————————————————————
P11609B
High/Excessive Flow
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Root Cause Unknown (First Level)
————————————————————————————————————————————————————————————
P116192
Performance or Incorrect Operation
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Insufficient Reagent Quality (First Level)
————————————————————————————————————————————————————————————
P116300
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – NOx Control Monitoring System (First Level)
————————————————————————————————————————————————————————————
P26047F
Measured voltage below limit
Actuator Stuck Off
Preheat relay problem or sense SC-.
Shorting wire may break when attempt
Preheat sense 1
Preheat relay
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1 Preheat relay
Intake Air Heater “A” Circuit Range/Performance
————————————————————————————————————————————————————————————
P115600
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power
Supply “A” Circuit High
————————————————————————————————————————————————————————————
P115700
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power
Supply “A” Circuit Low
————————————————————————————————————————————————————————————
P115800
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Reductant Control
Module Sensor Power Supply “B” Circuit High
————————————————————————————————————————————————————————————
P115900
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Reductant Control Module Sensor Power Supply “B” Circuit Low
————————————————————————————————————————————————————————————
P115A00
No Sub Type Information
Possible incread risk of crystalization
Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
Exhaust Gas Temperature Sensor Circuit Signal Compare Failure Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P115B00
No Sub Type Information
None
The sensor is stuck Leakage in exhaust system Leakage in intake system Sensor
Diagnostic Service 14. No additional action is needed
Check:
Leakage in exhaust system Leakage in intake system Sensor
Exhaust Gas Temperature Sensor Circuit Stuck Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P116441
General Checksum Failure
All ACM functionality disabled, no urea dosing
No software in ACM
.
Diagnostic Service 14. No additional action is needed
Check:
No software in ACM
Reductant Control Module Internal Control Module Memory Checksum Error
————————————————————————————————————————————————————————————
P116500
No Sub Type Information
Buzzer signal (alert), Display of the message, with bip, simultaneously with the gear engaged pictogram.
Driver is at low speed but still shifts to high gear, range high.
Protective measure for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective measure for clutch/transmission
Driver Selected Too High Gear
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P116600
No Sub Type Information
Buzzer signal (alert), Display of the message, with bip, simultaneously with the gear engaged pictogram.
Driver is at high speed but still down-shift to low gear, range low.
Protective measure for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective measure for clutch/transmission
Driver Selected Too Low Gear
————————————————————————————————————————————————————————————
P116700
No Sub Type Information
The starter motor is deactivated
The starter motor is deactivated due to that the PTO switch is active.
None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to that the PTO switch is active.
Starter Activated When PTO Is Active
————————————————————————————————————————————————————————————
P000041
General Checksum Failure
The engine can not be started
.
Diagnostic Service 14. No additional action is needed
.
Control Module
————————————————————————————————————————————————————————————
P24FF00
No Sub Type Information
If tank temp is too high, no urea dosing
Urea tank temp is too high Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
Reductant Temperature Too High
————————————————————————————————————————————————————————————
U1FFF68
Event Information
None
None
Diagnostic Service 14. No additional
action is needed
.
Factory Mode Active
————————————————————————————————————————————————————————————
P117A00
No Sub Type Information
Possible ammonia smell
SCR catalyst removed, Regent out of specification, Clogged dosing system Urea specification
Dosing system Catalyst deactivated
Diagnostic Service 14. No additional action is needed
Check:
Urea specification Dosing system Catalyst deactivated
SCR NOx Catalyst Efficiency Critically Below Threshold Bank 1
————————————————————————————————————————————————————————————
P047800
Measured voltage
above limit
No Sub Type
Information
Powerloss, engine break is
reduced
Broken actuator/Harness
AVU
Diagnostic Service 14. No additional
action is needed
Check:
AVU
Exhaust Pressure Control
Valve “A” High
————————————————————————————————————————————————————————————
P047700
Measured voltage below limit
No Sub Type Information
Powerloss, engine break is reduced
Broken actuator/Harness AVU
Diagnostic Service 14. No additional action is needed
Check: AVU
Exhaust Pressure Control Valve “A” Low
————————————————————————————————————————————————————————————
P047513
Measured voltage outside the limits specified by the
sensor
Circuit Open
Powerloss, engine break is reduced
Broken actuator/Harness AVU
Diagnostic Service 14. No additional action is needed
Check: AVU
Exhaust Pressure Control Valve “A”
————————————————————————————————————————————————————————————
P222764
Signal Plausibility Failure
Powerloss (minor) P3524:
Black smoke (minor)
The ambient air pressure is showing either too high or to low value.
(abnormal value) Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor ECM
Barometric Pressure Sensor “A” Circuit Range/Performance
————————————————————————————————————————————————————————————
P011513
Measured voltage outside the limits specified by the
sensor
Circuit Open
Engine is difficult to start. Idle run regulation is detoriated.
Harness Sensor
Sensor/Harness
Diagnostic Service 14. No additional action is needed
Check: Sensor/Harness
Engine Coolant Temperature Sensor 1
————————————————————————————————————————————————————————————
P020D25
Signal Shape /
Waveform Failure
.
Diagnostic Service 14. No additional
action is needed
.
Cylinder 4 Injection
Timing
————————————————————————————————————————————————————————————
P020E25
Signal Shape /
Waveform Failure
.
Diagnostic Service 14. No additional
action is needed
.
Cylinder 5 Injection
Timing
————————————————————————————————————————————————————————————
P020F25
Signal Shape / Waveform Failure
.
Diagnostic Service 14. No additional action is needed
.
Cylinder 6 Injection Timing
————————————————————————————————————————————————————————————
P020B25
Signal Shape /
Waveform Failure
.
Diagnostic Service 14. No additional
action is needed
.
Cylinder 2 Injection
Timing
————————————————————————————————————————————————————————————
P020C25
Signal Shape /
Waveform Failure
.
Diagnostic Service 14. No additional
action is needed
.
Cylinder 3 Injection
Timing
————————————————————————————————————————————————————————————
P205E1F
Circuit Intermittent
Urea tank temp sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor, Cables, Connectors
Reductant Tank Temperature Sensor Circuit Intermittent/Erratic
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P053E00
No Sub Type Information
Forced idle Engine shut down
The non-filtered pressure difference (between crankcase pressure and ambient air pressure) is/was above limit. (The fault code will remain during the entire driving cycle (unless reset).)
E.g. Blow-by at piston ring. NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Diagnostic Service 14. No additional action is needed
Check:
E.g. Blow-by at piston ring.
NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Crankcase Pressure Too High
————————————————————————————————————————————————————————————
P25AB00
Measured voltage
above limit
No Sub Type
Information
Possible black smoke during
start.
Harness/Broken actuator
Harness/Valve
Diagnostic Service 14. No additional
action is needed
Check:
Harness/Valve
Piston Cooling Oil Control
Circuit High
————————————————————————————————————————————————————————————
P25AA00
Measured voltage below limit
No Sub Type Information
No piston cooling=>major engine damage if high
loads.
Harness/Broken actuator Harness/Valve
Diagnostic Service 14. No additional action is needed
Check: Harness/Valve
Piston Cooling Oil Control Circuit Low
————————————————————————————————————————————————————————————
P010513
Measured voltage outside the limits specified by the sensor
Circuit Open
Powerloss
Connectors. Harness. Sensor
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Manifold Absolute Pressure/Barometric Pressure Sensor
————————————————————————————————————————————————————————————
P010800
Measured voltage above limit
No Sub Type Information
Powerloss
Connectors. Harness. Sensor
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Manifold Absolute Pressure/Barometric Pressure Sensor Circuit High
————————————————————————————————————————————————————————————
P010662
Signal Compare Failure
Powerloss Black smoke
The boost pressure sensor output is showing either too high or to low value.
(abnormal value) Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance
————————————————————————————————————————————————————————————
P25AE00
No Sub Type
Information
.
Diagnostic Service 14. No additional
action is needed
.
Piston Cooling Oil
Pressure Too Low
————————————————————————————————————————————————————————————
P25A913
Measured voltage outside the limits specified by the sensor
Circuit Open
Possible black smoke during start.
Harness/Broken actuator Harness/Valve
Diagnostic Service 14. No additional action is needed
Check: Harness/Valve
Piston Cooling Oil Control
————————————————————————————————————————————————————————————
P054070
Measured voltage above limit
Actuator Stuck On
Fuse for shorting wire breaks.
Sense wire SC+ or preheat relay broken
Preheat sense 1
Preheat relay
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1 Preheat relay
Intake Air Heater “A” Control
————————————————————————————————————————————————————————————
P225D00
No Sub Type Information
None except fault code and lamp
Sensor removed (measures surround air)
Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
NOx Sensor Performance – Signal Stuck Low Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P10F200
Measured voltage below limit
No Sub Type Information
None
Pressure switch / Harness Pressure switch/Harness
Diagnostic Service 14. No additional action is needed
Check:
Pressure switch/Harness
Air Filter Indicator Circuit Low
————————————————————————————————————————————————————————————
P10F300
Measured voltage
above limit
No Sub Type
Information
None
Harness
Diagnostic Service 14. No additional
action is needed
Check:
Harness
Air Filter Indicator Circuit
High
————————————————————————————————————————————————————————————
P22FB00
No Sub Type Information
Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
NOx Sensor Performance – Sensing Element Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P110F90
Stuck On
Stop switch can not be activated
Switch
Engine stop switch
Diagnostic Service 14. No additional action is needed
Check:
Engine stop switch
Engine Stop Switch Stuck
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P110400
No Sub Type Information
The engine can not be started
Bad software configuration Software download application
Diagnostic Service 14. No additional action is needed
Check:
Software download application
Factory Mode
————————————————————————————————————————————————————————————
P10F824
Signal Stuck High
.
Diagnostic Service 14. No additional
action is needed
.
Air Filter Clogged
————————————————————————————————————————————————————————————
P055A13
Measured voltage outside the limits specified by the sensor
Circuit Open
.
Diagnostic Service 14. No additional action is needed
.
Engine Oil Pressure Sensor/Switch “B”
————————————————————————————————————————————————————————————
P055B64
Signal Plausibility Failure
The control function closes the PCJ valve. When the fault is set, the PCJ oil pressure is forced to max (if calibrated so in the pcj_ function).
The sensor is stuck, has an offset or another kind of rationality fault. It could also be the valve that cannot be closed.
Sensor/Valve
Diagnostic Service 14. No additional action is needed
Check: Sensor/Valve
Piston Cooling Oil Pressure Sensor Range/Performance
————————————————————————————————————————————————————————————
P055D00
Measured voltage above limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Piston Cooling Oil Pressure Sensor Circuit
High
————————————————————————————————————————————————————————————
P112800
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Piston Cooling Oil Pressure Moderately Low
————————————————————————————————————————————————————————————
P029800
No Sub Type Information
Powerloss
Extreme driving conditions Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Engine Oil Over Temperature
————————————————————————————————————————————————————————————
P111600
No Sub Type Information
Intermittent Powerloss
VGT stuck, Wastegate stuck VGT Turbo, Wastegate
Diagnostic Service 14. No additional action is needed
Check:
VGT Turbo, Wastegate
Manifold Absolute Pressure Moderately Too
High
————————————————————————————————————————————————————————————
P111800
No Sub Type Information
Intermittent Powerloss
VGT stuck, Wastegate stuck VGT Turbo, Wastegate
Diagnostic Service 14. No additional action is needed
Check:
VGT Turbo, Wastegate
Manifold Absolute Pressure Too High
————————————————————————————————————————————————————————————
P111D00
No Sub Type
Information
.
Diagnostic Service 14. No additional
action is needed
.
Engine Coolant Level
Moderately Low
————————————————————————————————————————————————————————————
P111E00
No Sub Type Information
Powerloss
Extreme Driving conditions
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Engine Coolant Temperature Moderately High
————————————————————————————————————————————————————————————
P112500
No Sub Type Information
Powerloss
Extreme driving conditions Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Engine Oil Temperature Moderately High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U117888
It has not been possible to send frames on Vehicle Communication Powertrain CAN and It has not been possible to receive frames on Vehicle Communication Powertrain CAN
Bus off
.
Diagnostic Service 14. No additional action is needed
.
Vehicle Communication Powertrain CAN
————————————————————————————————————————————————————————————
P253913
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Low Pressure Fuel System Sensor Circuit
————————————————————————————————————————————————————————————
P254200
Measured voltage above limit
No Sub Type Information
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Low Pressure Fuel System Sensor Circuit High
————————————————————————————————————————————————————————————
P008A00
No Sub Type Information
Fuel injection can be affected.
High differential pressure over filter.
Leakage Filter
Sensor
Diagnostic Service 14. No additional action is needed
Check: Filter Sensor
Low Pressure Fuel System Pressure – Too Low
————————————————————————————————————————————————————————————
P113500
No Sub Type Information
Engine speed is limited (to commonly 1200rpm). VCB and EPG activated to lower espd below deactivation limit (commonly 1000rpm).
The non-filtered pressure difference (between crankcase pressure and ambient air pressure) is/was above limit. (The fault code will remain during the entire driving cycle (unless reset).)
E.g. Blow-by at piston ring. NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Diagnostic Service 14. No additional action is needed
Check:
E.g. Blow-by at piston ring.
NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Crankcase Pressure Relative To Ambient Pressure Too High
————————————————————————————————————————————————————————————
U000188
It has not been possible to send frames on High Speed CAN Communication Bus and It has not been possible to receive frames on High Speed CAN Communication Bus
Bus off
.
Diagnostic Service 14. No additional action is needed
.
CAN Communication Backbone 2 Net
————————————————————————————————————————————————————————————
U001088
It has not been possible to send frames on Medium Speed CAN Communication Bus and It has not been possible to receive frames on Medium Speed CAN Communication Bus
Bus off
.
Diagnostic Service 14. No additional action is needed
.
CAN Communication Backbone 1 Net
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U010187
Missing Message
ETC2 not responding
.
Diagnostic Service 14. No additional
action is needed
Check:
ETC2 not responding
Lost Communication with
TECU
————————————————————————————————————————————————————————————
P034031
No Signal
The engine start time will increase.
Possible loss of power
Sensor/Harness Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Camshaft Position Sensor “A” Bank 1 or Single Sensor
————————————————————————————————————————————————————————————
P034138
Signal Frequency Incorrect
The engine start time will increase.
Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Camshaft Position Sensor A Circuit Range/Performance
————————————————————————————————————————————————————————————
P052612
Measured voltage above limit
Circuit Short To Battery
Either
1. Fan will work as on/off fan. 100% fan speed if cooling is needed. Higher fuel consumption.
Or
2. Fan will work in open loop mode. Deteriorated fan control, but might not be noticable to driver.
Broken sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Fan Speed Sensor Circuit
————————————————————————————————————————————————————————————
P054300
Measured voltage outside the limits specified by the
sensor
No Sub Type Information
Might get start problems in cold climate.
Heating element or wire broken.
Preheat sense 1
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1
Intake Air Heater A Circuit Open
————————————————————————————————————————————————————————————
P054415
Measured voltage above limit
Circuit Short To Battery or Open
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Exhaust Gas Temperature Sensor Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P001676
Wrong Mounting Position
Fuel consumption increased
Bad correlation between cam and crank, engine transmission not correct
Engine transmission
Diagnostic Service 14. No additional action is needed
Check:
Engine transmission
Crankshaft Position – Camshaft Position Correlation
————————————————————————————————————————————————————————————
P02CD00
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 1 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02CF00
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 2 Fuel Injector Offset Learning at Max Limit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P02D100
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 3 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D300
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 4 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D500
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 5 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D700
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 6 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P033531
No Signal
Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running. Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankshaft Position Sensor “A”
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P033638
Signal Frequency Incorrect
Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running. Possible loss of power
Sensor monting Sensor/Lack of shims
Diagnostic Service 14. No additional action is needed
Check:
Sensor/Lack of shims
Crankshaft Position Sensor A Circuit Range/Performance
————————————————————————————————————————————————————————————
P033900
No Sub Type Information
The engine start time will increase.Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running.
Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankshaft Position Sensor A Circuit Intermittent
————————————————————————————————————————————————————————————
P060100
No Sub Type Information
Engine derate
signature failure
.
Diagnostic Service 14. No additional action is needed
Check: signature failure
Internal Control Module Memory Check Sum Error
————————————————————————————————————————————————————————————
P060700
No Sub Type Information
Not possible to reprogram ECU
.
Diagnostic Service 14. No additional action is needed
.
Control Module Performance
————————————————————————————————————————————————————————————
P06151C
Measured voltage outside the limits specified by the
sensor
Circuit Voltage Out of Range
Impossible to activate starter motor
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay
————————————————————————————————————————————————————————————
P061600
Measured voltage below limit
No Sub Type Information
EMS can not control starter
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Circuit Low
————————————————————————————————————————————————————————————
P061700
Measured voltage
above limit
No Sub Type
Information
Impossible to activate
starter motor.
Start relay/harness
Diagnostic Service 14. No additional
action is needed
Check:
Start relay/Harness
Starter Relay Circuit High
————————————————————————————————————————————————————————————
P066800
Measured voltage below limit
No Sub Type Information
None
Internal fault in ECM ECM
Diagnostic Service 14. No additional action is needed
Check: ECM
PCM/ECM/TCM Internal Temperature Sensor
Circuit Low
————————————————————————————————————————————————————————————
P06B100
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply A Circuit Low
————————————————————————————————————————————————————————————
P06B200
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply A Circuit High
————————————————————————————————————————————————————————————
P06B400
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply B Circuit Low
————————————————————————————————————————————————————————————
P06B500
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply B Circuit High
————————————————————————————————————————————————————————————
U300001
Measured voltage outside the limits specified by the sensor
General Electrical Failure
Possible damage on EMS system components depending on the high voltage (>36V)
Generator, external charger
Diagnostic Service 14. No additional action is needed
Check:
Generator, external charger
Electronic control unit
————————————————————————————————————————————————————————————
U300041
Program memory corruption
General Checksum Failure
The engine can not be started
No software
Software download application
Diagnostic Service 14. No additional action is needed
Check:
Software download application
Electronic control unit
————————————————————————————————————————————————————————————
P011013
Measured voltage outside the limits specified by the sensor
Circuit Open
Engine is running but could be difficult to start in cold climate.
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Intake Air Temperature Sensor 1 Bank 1
————————————————————————————————————————————————————————————
P011200
Measured voltage below limit
No Sub Type Information
Engine is running but could be difficult to start in cold climate.
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Intake Air Temperature Sensor 1 Circuit Low Bank 1
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P011700
Measured voltage below limit
No Sub Type Information
Engine is difficult to start. Idle run regulation is
detoriated.
Harness Sensor
Sensor/Harness
Diagnostic Service 14. No additional action is needed
Check: Sensor/Harness
Engine Coolant Temperature Circuit Low
————————————————————————————————————————————————————————————
P021700
No Sub Type Information
Powerloss
Extreme Driving conditions Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Engine Coolant Over Temperature Condition
————————————————————————————————————————————————————————————
P048013
Measured voltage outside the limits specified by the
sensor
Circuit Open
Fan runs at full speed. Increased fuel consumption may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit
————————————————————————————————————————————————————————————
P051A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankcase Pressure Sensor
————————————————————————————————————————————————————————————
P051D00
Measured voltage above limit
No Sub Type Information
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Engine High Resolution Crankcase Pressure
————————————————————————————————————————————————————————————
P052300
Measured voltage above limit
No Sub Type Information
Oil pressure shows 0 in the cluster. Engine is running.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Engine Oil Pressure Circuit High
————————————————————————————————————————————————————————————
P052400
No Sub Type Information
Low pressure, powerloss
Oil leakage, broken oil pump, clogged oil system Oil system
Diagnostic Service 14. No additional action is needed
Check:
Oil system
Engine Oil Pressure Too Low
————————————————————————————————————————————————————————————
P222800
Measured voltage below limit
No Sub Type Information
None
Internal fault in ECM Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor
ECM
Barometric Pressure Circuit Low
————————————————————————————————————————————————————————————
P222900
Measured voltage above limit
No Sub Type Information
None
Internal fault in ECM Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor
ECM
Barometric Pressure Circuit High
————————————————————————————————————————————————————————————
P226400
No Sub Type Information
None
No error: Used for indication
when priming pump is active
None
Diagnostic Service 14. No additional action is needed
Check:
No error: Used for indication when priming pump is active
Water in Fuel Sensor
————————————————————————————————————————————————————————————
P226600
Measured voltage
below limit
No Sub Type
Information
Will give water in fuel
indication.
Harness
Diagnostic Service 14. No additional
action is needed
Check:
Harness
Water In Fuel Indicator
Circuit Low
————————————————————————————————————————————————————————————
P226700
Measured voltage above limit
No Sub Type Information
Undetected water in fuel can lead to engine stop
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Water In Fuel Indicator Circuit High
————————————————————————————————————————————————————————————
P250C00
Measured voltage below limit
No Sub Type Information
Oil level can not be measured.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check:
Harness Sensor
Engine Oil Level Circuit Low
————————————————————————————————————————————————————————————
P250F00
No Sub Type Information
None
Critically low oil level Leakage
Leakage
Sensor
Diagnostic Service 14. No additional action is needed
Check: Leakage Sensor
Engine Oil Level Too Low
————————————————————————————————————————————————————————————
P255613
Measured voltage outside the limits specified by the sensor
Circuit Open
Coolant level can not be detected.
Harness Harness connector sensor
Diagnostic Service 14. No additional action is needed
Check: Harness connector sensor
Engine Coolant Level Sensor/Switch
————————————————————————————————————————————————————————————
P255900
Measured voltage above limit
No Sub Type Information
Coolant level can not be detected.
Harness Harness connector sensor
Diagnostic Service 14. No additional action is needed
Check: Harness connector sensor
Engine Coolant Level Circuit High
————————————————————————————————————————————————————————————
P256000
No Sub Type Information
Powerloss
Coolant level below range if not Harness
Coolant system
Diagnostic Service 14. No additional action is needed
Check:
Coolant system
Engine Coolant Level Low
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P108600
No Sub Type Information
None
Low oil level Leakage Leakage
Sensor
Diagnostic Service 14. No additional action is needed
Check: Leakage Sensor
Oil Level Moderately Low
————————————————————————————————————————————————————————————
U014100
Lost communication with the node on Medium Speed CAN Communication Bus
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With VMCU
————————————————————————————————————————————————————————————
U012A87
Lost communication with the node
Missing Message
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With CCIOM
————————————————————————————————————————————————————————————
P109000
No Sub Type Information
Display of the message, without bip, simultaneously with the gear engaged
pictogram
Driver started at too high gear at start
Protective alert for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective alert for clutch/transmission
Transmission High Gear At Start
————————————————————————————————————————————————————————————
P109641
General Checksum
Failure
Engine derate
.
Diagnostic Service 14. No additional
action is needed
.
Transmission Control Unit
————————————————————————————————————————————————————————————
P069200
Measured voltage above limit
No Sub Type Information
Fan runs at full speed. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit High
————————————————————————————————————————————————————————————
P069100
Measured voltage below limit
No Sub Type Information
Fan always deactivated or always activated if fault is
intermittent.
Broken actuator, wire or ECM driver output
Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit Low
————————————————————————————————————————————————————————————
U015500
Lost communication with the node on Medium Speed CAN Communication Bus
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With Instrument Panel Cluster (IPC) Control Module
————————————————————————————————————————————————————————————
P052013
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil pressure shows 0 in the cluster. Engine is running.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Pressure Sensor/Switch “A”
————————————————————————————————————————————————————————————
P066613
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Internal fault in ECM ECM
Diagnostic Service 14. No additional action is needed
Check: ECM
Control Module Internal Temperature Sensor “A”
————————————————————————————————————————————————————————————
P020113
Measured voltage outside the limits specified by the sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 1 Injector “A”
————————————————————————————————————————————————————————————
P020313
Measured voltage outside the limits specified by the sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 3 Injector “A”
————————————————————————————————————————————————————————————
P020413
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 4 Injector “A”
————————————————————————————————————————————————————————————
P020513
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 5 Injector “A”
————————————————————————————————————————————————————————————
P020613
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 6 Injector “A”
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P250A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil level can not be measured.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Level Sensor
————————————————————————————————————————————————————————————
P020213
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 2 Injector “A”
————————————————————————————————————————————————————————————
P100E18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 2
————————————————————————————————————————————————————————————
P100F18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 3
————————————————————————————————————————————————————————————
P101018
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 4
————————————————————————————————————————————————————————————
P101518
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 5
————————————————————————————————————————————————————————————
P101618
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 6
————————————————————————————————————————————————————————————
P101711
Measured voltage below limit
Circuit Short To Ground
High fuel consumption due to fuel leakage.
Broken solenoid, wire or ECM driver output
Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P101712
Measured voltage above limit
Circuit Short To Battery
Valve constantly shut.
Broken solenoid, wire or ECM driver output
Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P101713
Measured voltage outside the limits specified by the
sensor
Circuit Open
Valve constantly shut.
Broken solenoid or wire. Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P100211
Measured voltage below limit
Circuit Short To Ground
Induction air is hot. Preheat relay is impossible to turn off.
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Preheat Relay
————————————————————————————————————————————————————————————
P100212
Measured voltage above limit
Circuit Short To Battery
Preheat relay not activated. White smoke for cold start. Start problems in cold climate.
Preheat relay solenoid shorted
Preheat relay.
Diagnostic Service 14. No additional action is needed
Check: Preheat relay.
Preheat Relay
————————————————————————————————————————————————————————————
P100213
Measured voltage outside the limits specified by the sensor
Circuit Open
Preheat relay not activated. White smoke for cold start. Start problems in cold climate.
Harness or Preheat relay solenoid
Harness. Preheat relay.
Diagnostic Service 14. No additional action is needed
Check:
Harness. Preheat relay.
Preheat Relay
————————————————————————————————————————————————————————————
P100713
Measured voltage outside the limits specified by the sensor
Circuit Open
None
Pressure switch / Harness Pressure switch/Harness
Diagnostic Service 14. No additional action is needed
Check:
Pressure switch/Harness
Air Filter Indicator
————————————————————————————————————————————————————————————
P100D18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 1
————————————————————————————————————————————————————————————
P102111
Measured voltage below limit
Circuit Short To Ground
VCB can not be turned off. Causes engine to stop.
Engine impossible to
restart.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P102112
Measured voltage above limit
Circuit Short To Battery
VCB can not be turned on. Engine break function derated. Gear shift performance derated for some automatic transmission boxes.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
P102113
Measured voltage outside the limits specified by the sensor
Circuit Open
VCB can not be turned on. Engine break function derated. Gear shift performance derated for some automatic transmission boxes.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
P019513
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Temperature Sensor “A”
————————————————————————————————————————————————————————————
P026500
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 2 Short Circuit High
————————————————————————————————————————————————————————————
P026800
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 3 Short Circuit High
————————————————————————————————————————————————————————————
P027100
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 4 Short Circuit High
————————————————————————————————————————————————————————————
P027400
Measured voltage above limit
No Sub Type Information
Loss of power and uneven
running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 5 Short Circuit High
————————————————————————————————————————————————————————————
P027700
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 6 Short Circuit High
————————————————————————————————————————————————————————————
P054500
Measured voltage below limit
No Sub Type Information
None
Sensor/Harness
Diagnostic Service 14. No additional action is needed
Check: Sensor/Harness
Exhaust Gas Temperature Short Circuit Low
————————————————————————————————————————————————————————————
P019700
Measured voltage below limit
No Sub Type Information
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Oil Temperature Short Circuit Low
————————————————————————————————————————————————————————————
P026200
Measured voltage above limit
No Sub Type Information
Loss of power and uneven
running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 1 Short Circuit High
————————————————————————————————————————————————————————————
U016700
No Sub Type Information
The engine can not be started
Immobilizer unit not installed. (When Immo in Cluster is used, the Cluster maybe did not wake up properly)
Immo system
Diagnostic Service 14. No additional action is needed
Check:
Immo system
Lost Communication With Vehicle Immobilizer Control Module
————————————————————————————————————————————————————————————
U042600
No Sub Type Information
The engine can not be started
ECM and Immobilizer(or Cluster) unit security codes do not match.
Immo system
Diagnostic Service 14. No additional action is needed
Check:
Immo system
Invalid Data Received From Vehicle Immobilizer Control Module
————————————————————————————————————————————————————————————
P114000
No Sub Type Information
No VCB
low engine oil temperature
.
Diagnostic Service 14. No additional action is needed
Check:
low engine oil temperature
Volvo Compression Brake (VCB) Control Oil
Temperature Too Low
————————————————————————————————————————————————————————————
P114411
Measured voltage
below limit
Circuit Short To Ground
EMS can not control starter
Start relay/harness
Diagnostic Service 14. No additional
action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P114412
Measured voltage above limit
Circuit Short To Battery
Impossible to activate starter motor.
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Highside
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P114413
Measured voltage outside the limits specified by the
sensor
Circuit Open
Impossible to activate starter motor
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P021900
No Sub Type Information
Engine speed is limited (to commonly 1200rpm). VCB and EPD activated to lower espd below deactivation limit (commonly 1000rpm).
Engine is/was overspeeding. Engine could be running on oil, due to e.g. faulty crankcase oil filter.
Diagnostic Service 14. No additional action is needed
Check:
Engine could be running on oil, due to e.g. faulty crankcase oil filter.
Engine Overspeed Condition
————————————————————————————————————————————————————————————
P06E970
Actuator Stuck On
The starter motor is deactivated
The starter motor is deactivated due to that the cogwheels of the starter and engine are stuck
None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to that the cogwheels of the starter and engine are stuck
Engine Starter Performance
————————————————————————————————————————————————————————————
P06E998
Component or System Over Temperature
The starter motor is deactivated
The starter motor is deactivated due to overheat None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to overheat
Engine Starter Performance
————————————————————————————————————————————————————————————
P26047F
Measured voltage below limit
Actuator Stuck Off
Preheat relay problem or sense SC-.
Shorting wire may break when attempt
Preheat sense 1
Preheat relay
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1 Preheat relay
Intake Air Heater “A” Circuit Range/Performance
————————————————————————————————————————————————————————————
P116500
No Sub Type Information
Buzzer signal (alert), Display of the message, with bip, simultaneously with the gear engaged pictogram.
Driver is at low speed but still shifts to high gear, range high.
Protective measure for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective measure for clutch/transmission
Driver Selected Too High Gear
————————————————————————————————————————————————————————————
P116600
No Sub Type Information
Buzzer signal (alert), Display of the message, with bip, simultaneously with the gear engaged pictogram.
Driver is at high speed but still down-shift to low gear, range low.
Protective measure for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective measure for clutch/transmission
Driver Selected Too Low Gear
————————————————————————————————————————————————————————————
P116700
No Sub Type Information
The starter motor is deactivated
The starter motor is deactivated due to that the PTO switch is active.
None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to that the PTO switch is active.
Starter Activated When PTO Is Active
————————————————————————————————————————————————————————————
P000041
General Checksum
Failure
The engine can not be
started
.
Diagnostic Service 14. No additional
action is needed
.
Control Module
————————————————————————————————————————————————————————————
U1FFF68
Event Information
None
None
Diagnostic Service 14. No additional
action is needed
.
Factory Mode Active
————————————————————————————————————————————————————————————
P047800
Measured voltage
above limit
No Sub Type
Information
Powerloss, engine break is
reduced
Broken actuator/Harness
AVU
Diagnostic Service 14. No additional
action is needed
Check:
AVU
Exhaust Pressure Control
Valve “A” High
————————————————————————————————————————————————————————————
P047700
Measured voltage
below limit
No Sub Type
Information
Powerloss, engine break is
reduced
Broken actuator/Harness
AVU
Diagnostic Service 14. No additional
action is needed
Check:
AVU
Exhaust Pressure Control
Valve “A” Low
————————————————————————————————————————————————————————————
P047513
Measured voltage outside the limits specified by the sensor
Circuit Open
Powerloss, engine break is reduced
Broken actuator/Harness AVU
Diagnostic Service 14. No additional action is needed
Check: AVU
Exhaust Pressure Control Valve “A”
————————————————————————————————————————————————————————————
P011513
Measured voltage outside the limits specified by the
sensor
Circuit Open
Engine is difficult to start. Idle run regulation is detoriated.
Harness Sensor
Sensor/Harness
Diagnostic Service 14. No additional action is needed
Check: Sensor/Harness
Engine Coolant Temperature Sensor 1
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P053E00
No Sub Type Information
Forced idle Engine shut down
The non-filtered pressure difference (between crankcase pressure and ambient air pressure) is/was above limit. (The fault code will remain during the entire driving cycle (unless reset).)
E.g. Blow-by at piston ring. NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Diagnostic Service 14. No additional action is needed
Check:
E.g. Blow-by at piston ring.
NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Crankcase Pressure Too High
————————————————————————————————————————————————————————————
P010513
Measured voltage outside the limits specified by the sensor
Circuit Open
Powerloss
Connectors. Harness. Sensor
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Manifold Absolute Pressure/Barometric Pressure Sensor
————————————————————————————————————————————————————————————
P010800
Measured voltage above limit
No Sub Type Information
Powerloss
Connectors. Harness. Sensor
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Manifold Absolute Pressure/Barometric Pressure Sensor Circuit High
————————————————————————————————————————————————————————————
P054070
Measured voltage above limit
Actuator Stuck On
Fuse for shorting wire breaks.
Sense wire SC+ or preheat relay broken
Preheat sense 1
Preheat relay
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1 Preheat relay
Intake Air Heater “A” Control
————————————————————————————————————————————————————————————
P10F200
Measured voltage below limit
No Sub Type Information
None
Pressure switch / Harness Pressure switch/Harness
Diagnostic Service 14. No additional action is needed
Check:
Pressure switch/Harness
Air Filter Indicator Circuit Low
————————————————————————————————————————————————————————————
P10F300
Measured voltage
above limit
No Sub Type
Information
None
Harness
Diagnostic Service 14. No additional
action is needed
Check:
Harness
Air Filter Indicator Circuit
High
————————————————————————————————————————————————————————————
P110F90
Stuck On
Stop switch can not be
activated
Switch
Engine stop switch
Diagnostic Service 14. No additional
action is needed
Check:
Engine stop switch
Engine Stop Switch Stuck
————————————————————————————————————————————————————————————
P110400
No Sub Type Information
The engine can not be started
Bad software configuration Software download application
Diagnostic Service 14. No additional action is needed
Check:
Software download application
Factory Mode
————————————————————————————————————————————————————————————
P10F824
Signal Stuck High
.
Diagnostic Service 14. No additional action is needed
.
Air Filter Clogged
————————————————————————————————————————————————————————————
P029800
No Sub Type Information
Powerloss
Extreme driving conditions Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Engine Oil Over Temperature
————————————————————————————————————————————————————————————
P111600
No Sub Type Information
Intermittent Powerloss
VGT stuck, Wastegate stuck VGT Turbo, Wastegate
Diagnostic Service 14. No additional action is needed
Check:
VGT Turbo, Wastegate
Manifold Absolute
Pressure Moderately Too High
————————————————————————————————————————————————————————————
P111800
No Sub Type Information
Intermittent Powerloss
VGT stuck, Wastegate stuck VGT Turbo, Wastegate
Diagnostic Service 14. No additional action is needed
Check:
VGT Turbo, Wastegate
Manifold Absolute Pressure Too High
————————————————————————————————————————————————————————————
P111D00
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Engine Coolant Level Moderately Low
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P111E00
No Sub Type Information
Powerloss
Extreme Driving conditions
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Engine Coolant Temperature Moderately High
————————————————————————————————————————————————————————————
P112500
No Sub Type Information
Powerloss
Extreme driving conditions Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Engine Oil Temperature Moderately High
————————————————————————————————————————————————————————————
U117888
It has not been possible to send frames on Vehicle Communication Powertrain CAN and It has not been possible to receive frames on Vehicle Communication Powertrain CAN
Bus off
.
Diagnostic Service 14. No additional action is needed
.
Vehicle Communication Powertrain CAN
————————————————————————————————————————————————————————————
P253913
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Low Pressure Fuel System Sensor Circuit
————————————————————————————————————————————————————————————
P254200
Measured voltage above limit
No Sub Type Information
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Low Pressure Fuel System Sensor Circuit High
————————————————————————————————————————————————————————————
P008A00
No Sub Type Information
Fuel injection can be affected.
High differential pressure over filter.
Leakage Filter
Sensor
Diagnostic Service 14. No additional action is needed
Check: Filter Sensor
Low Pressure Fuel System Pressure – Too Low
————————————————————————————————————————————————————————————
P113500
No Sub Type Information
Engine speed is limited (to commonly 1200rpm). VCB and EPG activated to lower espd below deactivation limit (commonly 1000rpm).
The non-filtered pressure difference (between crankcase pressure and ambient air pressure) is/was above limit. (The fault code will remain during the entire driving cycle (unless reset).)
E.g. Blow-by at piston ring. NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Diagnostic Service 14. No additional action is needed
Check:
E.g. Blow-by at piston ring.
NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Crankcase Pressure Relative To Ambient Pressure Too High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U000188
It has not been possible to send frames on High Speed CAN Communication Bus and It has not been possible to receive frames on High Speed CAN Communication Bus
Bus off
.
Diagnostic Service 14. No additional action is needed
.
CAN Communication Backbone 2 Net
————————————————————————————————————————————————————————————
U001088
It has not been possible to send frames on Medium Speed CAN Communication Bus and It has not been possible to receive frames on Medium Speed CAN Communication Bus
Bus off
.
Diagnostic Service 14. No additional action is needed
.
CAN Communication Backbone 1 Net
————————————————————————————————————————————————————————————
U010187
Missing Message
ETC2 not responding
.
Diagnostic Service 14. No additional
action is needed
Check:
ETC2 not responding
Lost Communication with
TECU
————————————————————————————————————————————————————————————
P034031
No Signal
The engine start time will increase.
Possible loss of power
Sensor/Harness Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Camshaft Position Sensor “A” Bank 1 or Single
Sensor
————————————————————————————————————————————————————————————
P034138
Signal Frequency Incorrect
The engine start time will increase.
Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Camshaft Position Sensor A Circuit
Range/Performance
————————————————————————————————————————————————————————————
P052612
Measured voltage above limit
Circuit Short To Battery
Either
1. Fan will work as on/off fan. 100% fan speed if cooling is needed. Higher fuel consumption.
Or
2. Fan will work in open loop mode. Deteriorated fan control, but might not be noticable to driver.
Broken sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Fan Speed Sensor Circuit
————————————————————————————————————————————————————————————
P054300
Measured voltage outside the limits specified by the
sensor
No Sub Type Information
Might get start problems in cold climate.
Heating element or wire broken.
Preheat sense 1
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1
Intake Air Heater A Circuit Open
————————————————————————————————————————————————————————————
P054415
Measured voltage above limit
Circuit Short To Battery or Open
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Exhaust Gas Temperature Sensor Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P001676
Wrong Mounting Position
Fuel consumption increased
Bad correlation between cam and crank, engine transmission not correct Engine transmission
Diagnostic Service 14. No additional action is needed
Check:
Engine transmission
Crankshaft Position – Camshaft Position Correlation
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P02CD00
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 1 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02CF00
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 2 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D100
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 3 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D300
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 4 Fuel Injector Offset Learning at Max Limit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P02D500
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 5 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D700
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 6 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P033531
No Signal
Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running. Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankshaft Position Sensor “A”
————————————————————————————————————————————————————————————
P033638
Signal Frequency Incorrect
Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running. Possible loss of power
Sensor monting Sensor/Lack of shims
Diagnostic Service 14. No additional action is needed
Check:
Sensor/Lack of shims
Crankshaft Position Sensor A Circuit Range/Performance
————————————————————————————————————————————————————————————
P033900
No Sub Type Information
The engine start time will increase.Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running.
Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankshaft Position Sensor A Circuit Intermittent
————————————————————————————————————————————————————————————
P060100
No Sub Type Information
Engine derate
signature failure
.
Diagnostic Service 14. No additional action is needed
Check: signature failure
Internal Control Module Memory Check Sum Error
————————————————————————————————————————————————————————————
P060700
No Sub Type
Information
Not possible to reprogram
ECU
.
Diagnostic Service 14. No additional
action is needed
.
Control Module
Performance
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P06151C
Measured voltage outside the limits specified by the
sensor
Circuit Voltage Out of Range
Impossible to activate starter motor
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay
————————————————————————————————————————————————————————————
P061600
Measured voltage
below limit
No Sub Type
Information
EMS can not control starter
Start relay/harness
Diagnostic Service 14. No additional
action is needed
Check:
Start relay/Harness
Starter Relay Circuit Low
————————————————————————————————————————————————————————————
P061700
Measured voltage above limit
No Sub Type Information
Impossible to activate starter motor.
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Circuit High
————————————————————————————————————————————————————————————
P066800
Measured voltage below limit
No Sub Type Information
None
Internal fault in ECM ECM
Diagnostic Service 14. No additional action is needed
Check: ECM
PCM/ECM/TCM Internal Temperature Sensor
Circuit Low
————————————————————————————————————————————————————————————
P06B100
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply A Circuit Low
————————————————————————————————————————————————————————————
P06B200
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply A Circuit High
————————————————————————————————————————————————————————————
P06B400
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply B Circuit Low
————————————————————————————————————————————————————————————
P06B500
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply B Circuit High
————————————————————————————————————————————————————————————
U300001
Measured voltage outside the limits specified by the
sensor
General Electrical Failure
Possible damage on EMS system components depending on the high
voltage (>36V)
Generator, external charger
Diagnostic Service 14. No additional action is needed
Check:
Generator, external charger
Electronic control unit
————————————————————————————————————————————————————————————
U300041
Program memory corruption
General Checksum Failure
The engine can not be started
No software Software download
application
Diagnostic Service 14. No additional action is needed
Check:
Software download application
Electronic control unit
————————————————————————————————————————————————————————————
P011013
Measured voltage outside the limits specified by the
sensor
Circuit Open
Engine is running but could be difficult to start in cold climate.
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Intake Air Temperature Sensor 1 Bank 1
————————————————————————————————————————————————————————————
P011200
Measured voltage below limit
No Sub Type Information
Engine is running but could be difficult to start in cold climate.
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Intake Air Temperature Sensor 1 Circuit Low Bank 1
————————————————————————————————————————————————————————————
P011700
Measured voltage below limit
No Sub Type Information
Engine is difficult to start. Idle run regulation is detoriated.
Harness Sensor
Sensor/Harness
Diagnostic Service 14. No additional action is needed
Check: Sensor/Harness
Engine Coolant Temperature Circuit Low
————————————————————————————————————————————————————————————
P021700
No Sub Type Information
Powerloss
Extreme Driving conditions Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Engine Coolant Over Temperature Condition
————————————————————————————————————————————————————————————
P048013
Measured voltage outside the limits specified by the sensor
Circuit Open
Fan runs at full speed. Increased fuel consumption may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit
————————————————————————————————————————————————————————————
P051A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankcase Pressure Sensor
————————————————————————————————————————————————————————————
P051D00
Measured voltage above limit
No Sub Type Information
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Engine High Resolution Crankcase Pressure
————————————————————————————————————————————————————————————
P052300
Measured voltage above limit
No Sub Type Information
Oil pressure shows 0 in the cluster. Engine is running.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Engine Oil Pressure Circuit High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P052400
No Sub Type Information
Low pressure, powerloss
Oil leakage, broken oil pump, clogged oil system Oil system
Diagnostic Service 14. No additional action is needed
Check:
Oil system
Engine Oil Pressure Too Low
————————————————————————————————————————————————————————————
P222800
Measured voltage below limit
No Sub Type Information
None
Internal fault in ECM Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check:
Sensor ECM
Barometric Pressure Circuit Low
————————————————————————————————————————————————————————————
P222900
Measured voltage above limit
No Sub Type Information
None
Internal fault in ECM Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check:
Sensor ECM
Barometric Pressure Circuit High
————————————————————————————————————————————————————————————
P226400
No Sub Type Information
None
No error: Used for indication
when priming pump is active
None
Diagnostic Service 14. No additional action is needed
Check:
No error: Used for indication when priming pump is active
Water in Fuel Sensor
————————————————————————————————————————————————————————————
P226600
Measured voltage below limit
No Sub Type Information
Will give water in fuel indication.
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Water In Fuel Indicator Circuit Low
————————————————————————————————————————————————————————————
P226700
Measured voltage above limit
No Sub Type Information
Undetected water in fuel can lead to engine stop
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Water In Fuel Indicator Circuit High
————————————————————————————————————————————————————————————
P250C00
Measured voltage below limit
No Sub Type Information
Oil level can not be measured.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Engine Oil Level Circuit Low
————————————————————————————————————————————————————————————
P250F00
No Sub Type Information
None
Critically low oil level Leakage
Leakage
Sensor
Diagnostic Service 14. No additional action is needed
Check: Leakage Sensor
Engine Oil Level Too Low
————————————————————————————————————————————————————————————
P255613
Measured voltage outside the limits specified by the
sensor
Circuit Open
Coolant level can not be detected.
Harness Harness connector
sensor
Diagnostic Service 14. No additional action is needed
Check: Harness connector
sensor
Engine Coolant Level Sensor/Switch
————————————————————————————————————————————————————————————
P255900
Measured voltage above limit
No Sub Type Information
Coolant level can not be detected.
Harness Harness connector
sensor
Diagnostic Service 14. No additional action is needed
Check: Harness connector
sensor
Engine Coolant Level Circuit High
————————————————————————————————————————————————————————————
P256000
No Sub Type Information
Powerloss
Coolant level below range if not Harness
Coolant system
Diagnostic Service 14. No additional action is needed
Check:
Coolant system
Engine Coolant Level Low
————————————————————————————————————————————————————————————
P108600
No Sub Type Information
None
Low oil level Leakage Leakage Sensor
Diagnostic Service 14. No additional action is needed
Check: Leakage Sensor
Oil Level Moderately Low
————————————————————————————————————————————————————————————
U014100
Lost communication with the node on Medium Speed CAN Communication Bus
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With VMCU
————————————————————————————————————————————————————————————
U012A87
Lost communication with the node
Missing Message
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With CCIOM
————————————————————————————————————————————————————————————
P109000
No Sub Type Information
Display of the message, without bip, simultaneously with the gear engaged pictogram
Driver started at too high gear at start
Protective alert for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective alert for clutch/transmission
Transmission High Gear At Start
————————————————————————————————————————————————————————————
P109641
General Checksum
Failure
Engine derate
.
Diagnostic Service 14. No additional
action is needed
.
Transmission Control Unit
————————————————————————————————————————————————————————————
P069200
Measured voltage above limit
No Sub Type Information
Fan runs at full speed. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P069100
Measured voltage below limit
No Sub Type Information
Fan always deactivated or always activated if fault is
intermittent.
Broken actuator, wire or ECM driver output
Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit Low
————————————————————————————————————————————————————————————
U015500
Lost communication with the node on Medium Speed CAN Communication Bus
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With Instrument Panel Cluster (IPC) Control Module
————————————————————————————————————————————————————————————
P052013
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil pressure shows 0 in the cluster. Engine is running.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Pressure Sensor/Switch “A”
————————————————————————————————————————————————————————————
P066613
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Internal fault in ECM ECM
Diagnostic Service 14. No additional action is needed
Check: ECM
Control Module Internal Temperature Sensor “A”
————————————————————————————————————————————————————————————
P020113
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 1 Injector “A”
————————————————————————————————————————————————————————————
P020313
Measured voltage outside the limits specified by the sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 3 Injector “A”
————————————————————————————————————————————————————————————
P020413
Measured voltage outside the limits specified by the sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 4 Injector “A”
————————————————————————————————————————————————————————————
P020513
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 5 Injector “A”
————————————————————————————————————————————————————————————
P020613
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 6 Injector “A”
————————————————————————————————————————————————————————————
P250A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil level can not be measured.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Level Sensor
————————————————————————————————————————————————————————————
P020213
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 2 Injector “A”
————————————————————————————————————————————————————————————
P100E18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 2
————————————————————————————————————————————————————————————
P100F18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 3
————————————————————————————————————————————————————————————
P101018
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 4
————————————————————————————————————————————————————————————
P101518
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 5
————————————————————————————————————————————————————————————
P101618
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 6
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P101711
Measured voltage below limit
Circuit Short To Ground
High fuel consumption due to fuel leakage.
Broken solenoid, wire or ECM driver output
Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P101712
Measured voltage above limit
Circuit Short To Battery
Valve constantly shut.
Broken solenoid, wire or ECM driver output
Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P101713
Measured voltage outside the limits specified by the
sensor
Circuit Open
Valve constantly shut.
Broken solenoid or wire. Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P100211
Measured voltage below limit
Circuit Short To Ground
Induction air is hot. Preheat relay is impossible to turn
off.
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Preheat Relay
————————————————————————————————————————————————————————————
P100212
Measured voltage above limit
Circuit Short To Battery
Preheat relay not activated. White smoke for cold start. Start problems in cold climate.
Preheat relay solenoid shorted
Preheat relay.
Diagnostic Service 14. No additional action is needed
Check: Preheat relay.
Preheat Relay
————————————————————————————————————————————————————————————
P100213
Measured voltage outside the limits specified by the sensor
Circuit Open
Preheat relay not activated. White smoke for cold start. Start problems in cold climate.
Harness or Preheat relay solenoid
Harness. Preheat relay.
Diagnostic Service 14. No additional action is needed
Check:
Harness. Preheat relay.
Preheat Relay
————————————————————————————————————————————————————————————
P100713
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Pressure switch / Harness Pressure switch/Harness
Diagnostic Service 14. No additional action is needed
Check:
Pressure switch/Harness
Air Filter Indicator
————————————————————————————————————————————————————————————
P100D18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 1
————————————————————————————————————————————————————————————
P102111
Measured voltage below limit
Circuit Short To Ground
VCB can not be turned off. Causes engine to stop.
Engine impossible to
restart.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
P102112
Measured voltage above limit
Circuit Short To Battery
VCB can not be turned on. Engine break function derated. Gear shift performance derated for some automatic transmission boxes.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
P102113
Measured voltage outside the limits specified by the sensor
Circuit Open
VCB can not be turned on. Engine break function derated. Gear shift performance derated for some automatic transmission boxes.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
P019513
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Temperature Sensor “A”
————————————————————————————————————————————————————————————
P026500
Measured voltage above limit
No Sub Type Information
Loss of power and uneven
running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 2 Short Circuit High
————————————————————————————————————————————————————————————
P026800
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 3 Short Circuit High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P027100
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 4 Short Circuit High
————————————————————————————————————————————————————————————
P027400
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 5 Short Circuit High
————————————————————————————————————————————————————————————
P027700
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 6 Short Circuit High
————————————————————————————————————————————————————————————
P054500
Measured voltage below limit
No Sub Type Information
None
Sensor/Harness
Diagnostic Service 14. No additional action is needed
Check: Sensor/Harness
Exhaust Gas Temperature Short Circuit Low
————————————————————————————————————————————————————————————
P019700
Measured voltage below limit
No Sub Type Information
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check:
Harness Sensor
Oil Temperature Short Circuit Low
————————————————————————————————————————————————————————————
P026200
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 1 Short Circuit High
————————————————————————————————————————————————————————————
U016700
No Sub Type Information
The engine can not be started
Immobilizer unit not installed. (When Immo in Cluster is used, the Cluster maybe did not wake up properly)
Immo system
Diagnostic Service 14. No additional action is needed
Check:
Immo system
Lost Communication With Vehicle Immobilizer Control Module
————————————————————————————————————————————————————————————
U042600
No Sub Type Information
The engine can not be started
ECM and Immobilizer(or Cluster) unit security codes do not match.
Immo system
Diagnostic Service 14. No additional action is needed
Check:
Immo system
Invalid Data Received From Vehicle Immobilizer Control Module
————————————————————————————————————————————————————————————
P114000
No Sub Type Information
No VCB
low engine oil temperature
.
Diagnostic Service 14. No additional action is needed
Check:
low engine oil temperature
Volvo Compression Brake (VCB) Control Oil Temperature Too Low
————————————————————————————————————————————————————————————
P114411
Measured voltage below limit
Circuit Short To Ground
EMS can not control starter
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P114412
Measured voltage
above limit
Circuit Short To Battery
Impossible to activate
starter motor.
Start relay/harness
Diagnostic Service 14. No additional
action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P114413
Measured voltage outside the limits specified by the
sensor
Circuit Open
Impossible to activate starter motor
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P021900
No Sub Type Information
Engine speed is limited (to commonly 1200rpm). VCB and EPD activated to lower espd below deactivation limit (commonly 1000rpm).
Engine is/was overspeeding. Engine could be running on oil, due to e.g. faulty crankcase oil filter.
Diagnostic Service 14. No additional action is needed
Check:
Engine could be running on oil, due to e.g. faulty crankcase oil filter.
Engine Overspeed Condition
————————————————————————————————————————————————————————————
P06E970
Actuator Stuck On
The starter motor is deactivated
The starter motor is deactivated due to that the cogwheels of the starter and engine are stuck
None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to that the cogwheels of the starter and engine are stuck
Engine Starter Performance
————————————————————————————————————————————————————————————
P06E998
Component or System Over Temperature
The starter motor is deactivated
The starter motor is deactivated due to overheat None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to overheat
Engine Starter Performance
————————————————————————————————————————————————————————————
P26047F
Measured voltage below limit
Actuator Stuck Off
Preheat relay problem or sense SC-.
Shorting wire may break when attempt
Preheat sense 1
Preheat relay
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1 Preheat relay
Intake Air Heater “A” Circuit Range/Performance
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P116500
No Sub Type Information
Buzzer signal (alert), Display of the message, with bip, simultaneously with the gear engaged pictogram.
Driver is at low speed but still shifts to high gear, range high.
Protective measure for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective measure for clutch/transmission
Driver Selected Too High Gear
————————————————————————————————————————————————————————————
P116600
No Sub Type Information
Buzzer signal (alert), Display of the message, with bip, simultaneously with the gear engaged pictogram.
Driver is at high speed but still down-shift to low gear, range low.
Protective measure for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective measure for clutch/transmission
Driver Selected Too Low Gear
————————————————————————————————————————————————————————————
P116700
No Sub Type Information
The starter motor is deactivated
The starter motor is deactivated due to that the PTO switch is active.
None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to that the PTO switch is active.
Starter Activated When PTO Is Active
————————————————————————————————————————————————————————————
P000041
General Checksum
Failure
The engine can not be
started
.
Diagnostic Service 14. No additional
action is needed
.
Control Module
————————————————————————————————————————————————————————————
U1FFF68
Event Information
None
None
Diagnostic Service 14. No additional action is needed
.
Factory Mode Active
————————————————————————————————————————————————————————————
P047800
Measured voltage
above limit
No Sub Type
Information
Powerloss, engine break is
reduced
Broken actuator/Harness
AVU
Diagnostic Service 14. No additional
action is needed
Check:
AVU
Exhaust Pressure Control
Valve “A” High
————————————————————————————————————————————————————————————
P047700
Measured voltage
below limit
No Sub Type
Information
Powerloss, engine break is
reduced
Broken actuator/Harness
AVU
Diagnostic Service 14. No additional
action is needed
Check:
AVU
Exhaust Pressure Control
Valve “A” Low
————————————————————————————————————————————————————————————
P047513
Measured voltage outside the limits specified by the sensor
Circuit Open
Powerloss, engine break is reduced
Broken actuator/Harness AVU
Diagnostic Service 14. No additional action is needed
Check: AVU
Exhaust Pressure Control Valve “A”
————————————————————————————————————————————————————————————
P011513
Measured voltage outside the limits specified by the
sensor
Circuit Open
Engine is difficult to start. Idle run regulation is detoriated.
Harness Sensor
Sensor/Harness
Diagnostic Service 14. No additional action is needed
Check: Sensor/Harness
Engine Coolant Temperature Sensor 1
————————————————————————————————————————————————————————————
P053E00
No Sub Type Information
Forced idle Engine shut down
The non-filtered pressure difference (between crankcase pressure and ambient air pressure) is/was above limit. (The fault code will remain during the entire driving cycle (unless reset).)
E.g. Blow-by at piston ring. NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Diagnostic Service 14. No additional action is needed
Check:
E.g. Blow-by at piston ring.
NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Crankcase Pressure Too High
————————————————————————————————————————————————————————————
P010513
Measured voltage outside the limits specified by the sensor
Circuit Open
Powerloss
Connectors. Harness. Sensor
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Manifold Absolute Pressure/Barometric Pressure Sensor
————————————————————————————————————————————————————————————
P010800
Measured voltage above limit
No Sub Type Information
Powerloss
Connectors. Harness. Sensor
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Manifold Absolute Pressure/Barometric Pressure Sensor Circuit High
————————————————————————————————————————————————————————————
P054070
Measured voltage above limit
Actuator Stuck On
Fuse for shorting wire breaks.
Sense wire SC+ or preheat relay broken
Preheat sense 1
Preheat relay
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1 Preheat relay
Intake Air Heater “A” Control
————————————————————————————————————————————————————————————
P10F200
Measured voltage below limit
No Sub Type Information
None
Pressure switch / Harness Pressure switch/Harness
Diagnostic Service 14. No additional action is needed
Check:
Pressure switch/Harness
Air Filter Indicator Circuit Low
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P10F300
Measured voltage
above limit
No Sub Type
Information
None
Harness
Diagnostic Service 14. No additional
action is needed
Check:
Harness
Air Filter Indicator Circuit
High
————————————————————————————————————————————————————————————
P110F90
Stuck On
Stop switch can not be activated
Switch
Engine stop switch
Diagnostic Service 14. No additional action is needed
Check:
Engine stop switch
Engine Stop Switch Stuck
————————————————————————————————————————————————————————————
P110400
No Sub Type Information
The engine can not be started
Bad software configuration Software download application
Diagnostic Service 14. No additional action is needed
Check:
Software download application
Factory Mode
————————————————————————————————————————————————————————————
P10F824
Signal Stuck High
.
Diagnostic Service 14. No additional
action is needed
.
Air Filter Clogged
————————————————————————————————————————————————————————————
P029800
No Sub Type Information
Powerloss
Extreme driving conditions Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Engine Oil Over Temperature
————————————————————————————————————————————————————————————
P111600
No Sub Type Information
Intermittent Powerloss
VGT stuck, Wastegate stuck VGT Turbo, Wastegate
Diagnostic Service 14. No additional action is needed
Check:
VGT Turbo, Wastegate
Manifold Absolute Pressure Moderately Too High
————————————————————————————————————————————————————————————
P111800
No Sub Type Information
Intermittent Powerloss
VGT stuck, Wastegate stuck VGT Turbo, Wastegate
Diagnostic Service 14. No additional action is needed
Check:
VGT Turbo, Wastegate
Manifold Absolute Pressure Too High
————————————————————————————————————————————————————————————
P111D00
No Sub Type
Information
.
Diagnostic Service 14. No additional
action is needed
.
Engine Coolant Level
Moderately Low
————————————————————————————————————————————————————————————
P111E00
No Sub Type Information
Powerloss
Extreme Driving conditions
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Engine Coolant Temperature Moderately High
————————————————————————————————————————————————————————————
P112500
No Sub Type Information
Powerloss
Extreme driving conditions Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Engine Oil Temperature Moderately High
————————————————————————————————————————————————————————————
U117888
It has not been possible to send frames on Vehicle Communication Powertrain CAN and It has not been possible to receive frames on Vehicle Communication Powertrain CAN
Bus off
.
Diagnostic Service 14. No additional action is needed
.
Vehicle Communication Powertrain CAN
————————————————————————————————————————————————————————————
P253913
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Low Pressure Fuel System Sensor Circuit
————————————————————————————————————————————————————————————
P254200
Measured voltage above limit
No Sub Type Information
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Low Pressure Fuel System Sensor Circuit High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P008A00
No Sub Type Information
Fuel injection can be affected.
High differential pressure over filter.
Leakage Filter
Sensor
Diagnostic Service 14. No additional action is needed
Check: Filter Sensor
Low Pressure Fuel System Pressure – Too Low
————————————————————————————————————————————————————————————
P113500
No Sub Type Information
Engine speed is limited (to commonly 1200rpm). VCB and EPG activated to lower espd below deactivation limit (commonly 1000rpm).
The non-filtered pressure difference (between crankcase pressure and ambient air pressure) is/was above limit. (The fault code will remain during the entire driving cycle (unless reset).)
E.g. Blow-by at piston ring. NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Diagnostic Service 14. No additional action is needed
Check:
E.g. Blow-by at piston ring.
NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Crankcase Pressure Relative To Ambient Pressure Too High
————————————————————————————————————————————————————————————
U000188
It has not been possible to send frames on High Speed CAN Communication Bus and It has not been possible to receive frames on High Speed CAN Communication Bus
Bus off
.
Diagnostic Service 14. No additional action is needed
.
CAN Communication Backbone 2 Net
————————————————————————————————————————————————————————————
U001088
It has not been possible to send frames on Medium Speed CAN Communication Bus and It has not been possible to receive frames on Medium Speed CAN Communication Bus
Bus off
.
Diagnostic Service 14. No additional action is needed
.
CAN Communication Backbone 1 Net
————————————————————————————————————————————————————————————
U010187
Missing Message
ETC2 not responding
.
Diagnostic Service 14. No additional
action is needed
Check:
ETC2 not responding
Lost Communication with
TECU
————————————————————————————————————————————————————————————
P034031
No Signal
The engine start time will increase.
Possible loss of power
Sensor/Harness Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Camshaft Position Sensor “A” Bank 1 or Single Sensor
————————————————————————————————————————————————————————————
P034138
Signal Frequency Incorrect
The engine start time will increase.
Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Camshaft Position Sensor A Circuit Range/Performance
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P052612
Measured voltage above limit
Circuit Short To Battery
Either
1. Fan will work as on/off fan. 100% fan speed if cooling is needed. Higher fuel consumption.
Or
2. Fan will work in open loop mode. Deteriorated fan control, but might not be noticable to driver.
Broken sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Fan Speed Sensor Circuit
————————————————————————————————————————————————————————————
P054300
Measured voltage outside the limits specified by the sensor
No Sub Type Information
Might get start problems in cold climate.
Heating element or wire broken.
Preheat sense 1
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1
Intake Air Heater A Circuit Open
————————————————————————————————————————————————————————————
P001676
Wrong Mounting Position
Fuel consumption increased
Bad correlation between cam and crank, engine transmission not correct Engine transmission
Diagnostic Service 14. No additional action is needed
Check:
Engine transmission
Crankshaft Position – Camshaft Position Correlation
————————————————————————————————————————————————————————————
P007100
No Sub Type Information
Ambient air temp sensor or boost temp sensor faulty Ambient air temp sensor or Boost temp sensor
Diagnostic Service 14. No additional action is needed
Check:
Ambient air temp sensor or Boost temp sensor
Ambient Air Temperature Sensor Range/Performance
————————————————————————————————————————————————————————————
P02CD00
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 1 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02CF00
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 2 Fuel Injector Offset Learning at Max Limit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P02D100
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 3 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D300
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 4 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D500
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 5 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D700
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 6 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P033531
No Signal
Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running. Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankshaft Position Sensor “A”
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P033638
Signal Frequency Incorrect
Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running. Possible loss of power
Sensor monting Sensor/Lack of shims
Diagnostic Service 14. No additional action is needed
Check:
Sensor/Lack of shims
Crankshaft Position Sensor A Circuit Range/Performance
————————————————————————————————————————————————————————————
P033900
No Sub Type Information
The engine start time will increase.Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running.
Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankshaft Position Sensor A Circuit Intermittent
————————————————————————————————————————————————————————————
P203F00
No Sub Type Information
No urea dosing
Urea symbol in cluster
Tank almost empty, stop dosing to maintain cooling ECM interpretation of raw value. Urea level. DST problem.
Diagnostic Service 14. No additional action is needed
Check:
ECM interpretation of raw value. Urea level. DST problem.
Reductant Level Low
————————————————————————————————————————————————————————————
P205A13
Measured voltage outside the limits specified by the sensor
Circuit Open
None
AdBlue tank temp sensor Cables
Connectors
Urea tank temp sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor, Cables, Connectors
Reductant Tank Temperature Sensor
————————————————————————————————————————————————————————————
P208064
Signal Plausibility Failure
None
The sensor is not plausible Leakage in exhaust system Leakage in intake system Sensor
Diagnostic Service 14. No additional action is needed
Check:
Leakage in exhaust system Leakage in intake system Sensor
Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P220013
Measured voltage outside the limits specified by the sensor
Circuit Open
Cabling between Nox- sensor and Nox-sensor ECU Nox-sensor
Nox-sensor cabling Nox-sensor
Diagnostic Service 14. No additional action is needed
Check:
Nox-sensor cabling Nox-sensor
NOx Sensor Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P220164
Signal Plausibility Failure
Excessive urea dosing (only for SCR system)
Exhaust system leakage Air intake leakage
Nox-sensor
Dosing system (only for SCR system)
Exhaust system Air intake system
Nox-sensor
Diagnostic Service 14. No additional action is needed
Check:
Dosing system (only for SCR system) Exhaust system
Air intake system Nox-sensor
NOx Sensor Circuit Range/Performance
————————————————————————————————————————————————————————————
P060100
No Sub Type Information
Engine derate
signature failure
.
Diagnostic Service 14. No additional action is needed
Check: signature failure
Internal Control Module Memory Check Sum Error
————————————————————————————————————————————————————————————
P060700
No Sub Type
Information
Not possible to reprogram
ECU
.
Diagnostic Service 14. No additional
action is needed
.
Control Module
Performance
————————————————————————————————————————————————————————————
P06151C
Measured voltage outside the limits specified by the sensor
Circuit Voltage Out of Range
Impossible to activate starter motor
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P061600
Measured voltage
below limit
No Sub Type
Information
EMS can not control starter
Start relay/harness
Diagnostic Service 14. No additional
action is needed
Check:
Start relay/Harness
Starter Relay Circuit Low
————————————————————————————————————————————————————————————
P061700
Measured voltage above limit
No Sub Type Information
Impossible to activate starter motor.
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Circuit High
————————————————————————————————————————————————————————————
P066800
Measured voltage below limit
No Sub Type Information
None
Internal fault in ECM ECM
Diagnostic Service 14. No additional action is needed
Check: ECM
PCM/ECM/TCM Internal
Temperature Sensor Circuit Low
————————————————————————————————————————————————————————————
P06B100
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply A Circuit Low
————————————————————————————————————————————————————————————
P06B200
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply A Circuit High
————————————————————————————————————————————————————————————
P06B400
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply B Circuit Low
————————————————————————————————————————————————————————————
P06B500
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply B Circuit High
————————————————————————————————————————————————————————————
P20EE00
No Sub Type Information
NOx-conversion reduced by appr. 50%
Possible ammonia smell
Regent out of specification, Dosing performance low Urea specification
Dosing system
Diagnostic Service 14. No additional action is needed
Check:
Urea specification Dosing system
SCR NOx Catalyst Efficiency Below Threshold (Bank 1)
————————————————————————————————————————————————————————————
P260013
Measured voltage outside the limits specified by the sensor
Circuit Open
Pump always at half speed. High coolant temperatures may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Coolant Pump Control Circuit/Open
————————————————————————————————————————————————————————————
P260200
Measured voltage below limit
No Sub Type Information
Pump always runs at full speed. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Coolant Pump Control Circuit Low
————————————————————————————————————————————————————————————
P260300
Measured voltage above limit
No Sub Type Information
Pump always at half speed. High coolant temperatures may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Coolant Pump Control Circuit High
————————————————————————————————————————————————————————————
P261087
Missing Message
Timestamps from Cluster not available
J1708 time data failure and J1939 message does not exist. (Cluster error).
Cluster
Diagnostic Service 14. No additional action is needed
Check: Cluster
ECM/PCM Internal Engine Off Timer Performance
————————————————————————————————————————————————————————————
P2BA700
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Empty Reagent Tank
————————————————————————————————————————————————————————————
P023400
No Sub Type Information
Too high pressure Turbine , Compressor
Diagnostic Service 14. No additional action is needed
Check:
Turbine , Compressor
Turbocharger/Supercharg er Overboost Condition
————————————————————————————————————————————————————————————
P029900
No Sub Type Information
Too low pressure
Boost leakage, wastegate, VGT, compressor.
Diagnostic Service 14. No additional action is needed
Check:
Boost leakage, wastegate, VGT, compressor.
Turbocharger/Supercharg er Underboost
————————————————————————————————————————————————————————————
U300001
Measured voltage outside the limits specified by the sensor
General Electrical Failure
Possible damage on EMS system components depending on the high voltage (>36V)
Generator, external charger
Diagnostic Service 14. No additional action is needed
Check:
Generator, external charger
Electronic control unit
————————————————————————————————————————————————————————————
U300041
Program memory corruption
General Checksum Failure
The engine can not be started
No software Software download
application
Diagnostic Service 14. No additional action is needed
Check:
Software download application
Electronic control unit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P007087
Missing Message
None
J1708 and CAN ambient air temperature message does not exist.
Harness. Cluster
Diagnostic Service 14. No additional action is needed
Check:
Harness. Cluster
Ambient Air Temperature Sensor “A”
————————————————————————————————————————————————————————————
P011013
Measured voltage outside the limits specified by the
sensor
Circuit Open
Engine is running but could be difficult to start in cold climate.
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Intake Air Temperature Sensor 1 Bank 1
————————————————————————————————————————————————————————————
P011200
Measured voltage below limit
No Sub Type Information
Engine is running but could be difficult to start in cold climate.
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Intake Air Temperature Sensor 1 Circuit Low Bank 1
————————————————————————————————————————————————————————————
P011700
Measured voltage below limit
No Sub Type Information
Engine is difficult to start. Idle run regulation is
detoriated.
Harness Sensor
Sensor/Harness
Diagnostic Service 14. No additional action is needed
Check: Sensor/Harness
Engine Coolant Temperature Circuit Low
————————————————————————————————————————————————————————————
P021700
No Sub Type Information
Powerloss
Extreme Driving conditions Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Engine Coolant Over Temperature Condition
————————————————————————————————————————————————————————————
P047013
Measured voltage outside the limits specified by the sensor
Circuit Open
Open loop control enabled. Decreased brake power.
.
Diagnostic Service 14. No additional action is needed
.
Exhaust Pressure Sensor “A”
————————————————————————————————————————————————————————————
P047164
Signal Plausibility Failure
Open loop control enabled. Decreased brake power.
sensor, Closed loop butterfly, AVU sensor, butterfly, AVU
Diagnostic Service 14. No additional action is needed
Check:
sensor, butterfly, AVU
Engine Exhaust Back Pressure Circuit Range/Performance
————————————————————————————————————————————————————————————
P047300
Measured voltage above limit
No Sub Type Information
Open loop control enabled. Decreased brake power.
.
Diagnostic Service 14. No additional action is needed
.
Engine Exhaust Back Pressure Circuit High
————————————————————————————————————————————————————————————
P048013
Measured voltage outside the limits specified by the sensor
Circuit Open
Fan runs at full speed. Increased fuel consumption may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit
————————————————————————————————————————————————————————————
P051B64
Signal Plausibility Failure
Powerloss (minor) P3524:
Black smoke (minor)
The crank case pressure is showing either too high or to low value.
(abnormal value) Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor ECM
Engine High Resolution Crankcase Pressure Circuit Range/Performance
————————————————————————————————————————————————————————————
P051A13
Measured voltage outside the limits specified by the sensor
Circuit Open
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankcase Pressure Sensor
————————————————————————————————————————————————————————————
P051D00
Measured voltage above limit
No Sub Type Information
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine High Resolution Crankcase Pressure
————————————————————————————————————————————————————————————
P052300
Measured voltage above limit
No Sub Type Information
Oil pressure shows 0 in the cluster. Engine is running.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Pressure Circuit High
————————————————————————————————————————————————————————————
P052400
No Sub Type Information
Low pressure, powerloss
Oil leakage, broken oil pump, clogged oil system Oil system
Diagnostic Service 14. No additional action is needed
Check:
Oil system
Engine Oil Pressure Too Low
————————————————————————————————————————————————————————————
P222800
Measured voltage below limit
No Sub Type Information
None
Internal fault in ECM Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor
ECM
Barometric Pressure Circuit Low
————————————————————————————————————————————————————————————
P222900
Measured voltage above limit
No Sub Type Information
None
Internal fault in ECM Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor ECM
Barometric Pressure Circuit High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P226400
No Sub Type Information
None
No error: Used for indication
when priming pump is active
None
Diagnostic Service 14. No additional action is needed
Check:
No error: Used for indication when priming pump is active
Water in Fuel Sensor
————————————————————————————————————————————————————————————
P226600
Measured voltage
below limit
No Sub Type
Information
Will give water in fuel
indication.
Harness
Diagnostic Service 14. No additional
action is needed
Check:
Harness
Water In Fuel Indicator
Circuit Low
————————————————————————————————————————————————————————————
P226700
Measured voltage above limit
No Sub Type Information
Undetected water in fuel can lead to engine stop
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Water In Fuel Indicator Circuit High
————————————————————————————————————————————————————————————
P250C00
Measured voltage below limit
No Sub Type Information
Oil level can not be measured.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Engine Oil Level Circuit Low
————————————————————————————————————————————————————————————
P250F00
No Sub Type Information
None
Critically low oil level Leakage
Leakage
Sensor
Diagnostic Service 14. No additional action is needed
Check: Leakage Sensor
Engine Oil Level Too Low
————————————————————————————————————————————————————————————
P255613
Measured voltage outside the limits specified by the
sensor
Circuit Open
Coolant level can not be detected.
Harness Harness connector
sensor
Diagnostic Service 14. No additional action is needed
Check: Harness connector
sensor
Engine Coolant Level Sensor/Switch
————————————————————————————————————————————————————————————
P255900
Measured voltage above limit
No Sub Type Information
Coolant level can not be detected.
Harness Harness connector
sensor
Diagnostic Service 14. No additional action is needed
Check: Harness connector
sensor
Engine Coolant Level Circuit High
————————————————————————————————————————————————————————————
P256000
No Sub Type Information
Powerloss
Coolant level below range if not Harness
Coolant system
Diagnostic Service 14. No additional action is needed
Check:
Coolant system
Engine Coolant Level Low
————————————————————————————————————————————————————————————
P108600
No Sub Type Information
None
Low oil level Leakage Leakage
Sensor
Diagnostic Service 14. No additional action is needed
Check: Leakage Sensor
Oil Level Moderately Low
————————————————————————————————————————————————————————————
P20BF00
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Reagent Hose Heater 2 Short Circuit Low
————————————————————————————————————————————————————————————
U014100
Lost communication with the node on Medium Speed CAN Communication Bus
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With VMCU
————————————————————————————————————————————————————————————
U012A87
Lost communication with the node
Missing Message
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With CCIOM
————————————————————————————————————————————————————————————
P109000
No Sub Type Information
Display of the message, without bip, simultaneously with the gear engaged pictogram
Driver started at too high gear at start
Protective alert for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective alert for clutch/transmission
Transmission High Gear At Start
————————————————————————————————————————————————————————————
P208E00
No Sub Type Information
No urea dosing
Sensor/Harness dosing valve
injector, clogged hoses
Diagnostic Service 14. No additional action is needed
Check:
dosing valve
injector, clogged hoses
Aftertreatment Reagent Dosing Valve Clogged
————————————————————————————————————————————————————————————
P109541
General Checksum Failure
Engine derate
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Control Unit
————————————————————————————————————————————————————————————
P109641
General Checksum
Failure
Engine derate
.
Diagnostic Service 14. No additional
action is needed
.
Transmission Control Unit
————————————————————————————————————————————————————————————
P069200
Measured voltage above limit
No Sub Type Information
Fan runs at full speed. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P069100
Measured voltage below limit
No Sub Type Information
Fan always deactivated or always activated if fault is
intermittent.
Broken actuator, wire or ECM driver output
Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit Low
————————————————————————————————————————————————————————————
U015500
Lost communication with the node on Medium Speed CAN Communication Bus
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With Instrument Panel Cluster (IPC) Control Module
————————————————————————————————————————————————————————————
P052013
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil pressure shows 0 in the cluster. Engine is running.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Pressure Sensor/Switch “A”
————————————————————————————————————————————————————————————
P066613
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Internal fault in ECM ECM
Diagnostic Service 14. No additional action is needed
Check: ECM
Control Module Internal Temperature Sensor “A”
————————————————————————————————————————————————————————————
P020113
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 1 Injector “A”
————————————————————————————————————————————————————————————
P020313
Measured voltage outside the limits specified by the sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 3 Injector “A”
————————————————————————————————————————————————————————————
P020413
Measured voltage outside the limits specified by the sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 4 Injector “A”
————————————————————————————————————————————————————————————
P020513
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 5 Injector “A”
————————————————————————————————————————————————————————————
P020613
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 6 Injector “A”
————————————————————————————————————————————————————————————
P220E93
No Operation
Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
NOx Sensor Heater Control Circuit Range/Performance (Bank
1 Sensor 1)
————————————————————————————————————————————————————————————
P250A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil level can not be measured.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Level Sensor
————————————————————————————————————————————————————————————
P020213
Measured voltage outside the limits specified by the sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 2 Injector “A”
————————————————————————————————————————————————————————————
P100E18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 2
————————————————————————————————————————————————————————————
P100F18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 3
————————————————————————————————————————————————————————————
P101018
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 4
————————————————————————————————————————————————————————————
P101518
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 5
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P101618
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 6
————————————————————————————————————————————————————————————
P101711
Measured voltage below limit
Circuit Short To Ground
High fuel consumption due to fuel leakage.
Broken solenoid, wire or ECM driver output
Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P101712
Measured voltage above limit
Circuit Short To Battery
Valve constantly shut.
Broken solenoid, wire or ECM driver output
Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P101713
Measured voltage outside the limits specified by the
sensor
Circuit Open
Valve constantly shut.
Broken solenoid or wire. Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P220300
No Sub Type Information
Cabling between Nox- sensor and Nox-sensor ECU Nox-sensor
Nox-sensor cabling Nox-sensor
Diagnostic Service 14. No additional action is needed
Check:
Nox-sensor cabling Nox-sensor
NOx Sensor Circuit High Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P2BA800
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Interruption of Reagent Dosing Activity
————————————————————————————————————————————————————————————
P2BA900
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Insufficient Reagent Quality
————————————————————————————————————————————————————————————
P2BAA00
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Low Reagent Consumption
————————————————————————————————————————————————————————————
P2BAD00
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Root Cause Unknown
————————————————————————————————————————————————————————————
P2BAE96
Component Internal Failure
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – NOx Control Monitoring System
————————————————————————————————————————————————————————————
P100211
Measured voltage below limit
Circuit Short To Ground
Induction air is hot. Preheat relay is impossible to turn off.
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Preheat Relay
————————————————————————————————————————————————————————————
P100212
Measured voltage above limit
Circuit Short To Battery
Preheat relay not activated. White smoke for cold start. Start problems in cold climate.
Preheat relay solenoid shorted
Preheat relay.
Diagnostic Service 14. No additional action is needed
Check: Preheat relay.
Preheat Relay
————————————————————————————————————————————————————————————
P100213
Measured voltage outside the limits specified by the sensor
Circuit Open
Preheat relay not activated. White smoke for cold start. Start problems in cold climate.
Harness or Preheat relay solenoid
Harness. Preheat relay.
Diagnostic Service 14. No additional action is needed
Check:
Harness. Preheat relay.
Preheat Relay
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P100629
Signal invalid
None
The boost temperature sensor output is showing constant value.
Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Intake Air Temperature Sensor 1 Stuck Bank 1
————————————————————————————————————————————————————————————
P100713
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Pressure switch / Harness Pressure switch/Harness
Diagnostic Service 14. No additional action is needed
Check:
Pressure switch/Harness
Air Filter Indicator
————————————————————————————————————————————————————————————
P100D18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 1
————————————————————————————————————————————————————————————
P102111
Measured voltage below limit
Circuit Short To Ground
VCB can not be turned off. Causes engine to stop.
Engine impossible to
restart.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
P102112
Measured voltage above limit
Circuit Short To Battery
VCB can not be turned on. Engine break function derated. Gear shift performance derated for some automatic transmission boxes.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
P102113
Measured voltage outside the limits specified by the sensor
Circuit Open
VCB can not be turned on. Engine break function derated. Gear shift performance derated for some automatic transmission boxes.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
U010E00
Lost communication with the node
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With
Reductant Control Module
————————————————————————————————————————————————————————————
P019513
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Temperature Sensor “A”
————————————————————————————————————————————————————————————
P204A13
Measured voltage outside the limits specified by the sensor
Circuit Open
No urea dosing
ACM Pump module: AdBlue pressure sensor
ACM Pump module: Internal cabling
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Diagnostic Service 14. No additional action is needed
Check:
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Reductant Pressure Sensor
————————————————————————————————————————————————————————————
P203D00
Measured voltage above limit
No Sub Type Information
None
AdBlue tank level sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
AdBlue tank level sensor, Cables, Connectors
Aftertreatment Reagent Level Short Circuit High
————————————————————————————————————————————————————————————
P208A13
Measured voltage outside the limits specified by the sensor
Circuit Open
No urea dosing
Wiring harness internal error in pump
Diagnostic Service 14. No additional action is needed
Check:
Wiring harness internal error in pump
Reductant Pump “A” Control
————————————————————————————————————————————————————————————
P026500
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 2 Short Circuit High
————————————————————————————————————————————————————————————
P026800
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 3 Short Circuit High
————————————————————————————————————————————————————————————
P027100
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 4 Short Circuit High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P027400
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 5 Short Circuit High
————————————————————————————————————————————————————————————
P027700
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 6 Short Circuit High
————————————————————————————————————————————————————————————
P20B300
Measured voltage below limit
No Sub Type Information
None
.
Diagnostic Service 14. No additional action is needed
.
Reductant Heater Coolant Control Valve Circuit Low
————————————————————————————————————————————————————————————
P204800
Measured voltage below limit
No Sub Type Information
No urea dosing
ACM Pump module: DCU ACM Pump module: internal cabling
ACM Pump module: DCU,
ACM Pump module: internal cabling
Diagnostic Service 14. No additional action is needed
Check:
ACM Pump module: DCU, ACM Pump module: internal cabling
Aftertreatment Reagent Dosing Valve Short Circuit Low
————————————————————————————————————————————————————————————
P204713
Measured voltage outside the limits specified by the sensor
Circuit Open
no urea dosing
Cable / Connectors
ACM Dosing module: Dosing valve
Cable / Connectors ACM Dosing module: Dosing
valve
Diagnostic Service 14. No additional action is needed
Check:
Cable / Connectors ACM Dosing module: Dosing valve
Reductant Injection Valve Control Bank 1 Unit 1
————————————————————————————————————————————————————————————
P20C300
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Reagent Hose Heater 3 Short
Circuit Low
————————————————————————————————————————————————————————————
P20BB00
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Reagent Hose Heater 1 Short
Circuit Low
————————————————————————————————————————————————————————————
P20A200
Measured voltage below limit
No Sub Type Information
Not possible to perform afterrun
Internal electrical failure in valve within the ACM
Diagnostic Service 14. No additional action is needed
Check:
Internal electrical failure in valve within the ACM
Aftertreatment Reagent Direction Valve Short
Circuit Low
————————————————————————————————————————————————————————————
P065900
Measured voltage above limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
ACM Actuator High Supply 1 Short Circuit
High
————————————————————————————————————————————————————————————
P065800
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
ACM Actuator High Supply 1 Short Circuit Low
————————————————————————————————————————————————————————————
P208D00
Measured voltage above limit
No Sub Type Information
No urea dosing
Wiring harness internal error in pump
Diagnostic Service 14. No additional action is needed
Check:
Wiring harness internal error in pump
Aftertreatment Reagent
Pump Control Short Circut High
————————————————————————————————————————————————————————————
P208C00
Measured voltage below limit
No Sub Type Information
No urea dosing
Wiring harness internal error in pump
Diagnostic Service 14. No additional action is needed
Check:
Wiring harness internal error in pump
Aftertreatment Reagent Pump Control Short
Circuit Low
————————————————————————————————————————————————————————————
P203A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
AdBlue tank level sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
AdBlue tank level sensor, Cables, Connectors
Reductant Level Sensor “A”
————————————————————————————————————————————————————————————
P019700
Measured voltage below limit
No Sub Type Information
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check:
Harness Sensor
Oil Temperature Short Circuit Low
————————————————————————————————————————————————————————————
P024313
Measured voltage outside the limits specified by the
sensor
Circuit Open
Powerloss
Broken actuator or wire. Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Turbocharger/Supercharg er Wastegate Solenoid “A”
————————————————————————————————————————————————————————————
P024471
Actuator Stuck
Possible turbo damage
Wategate mechanically damaged
Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Wastegate Stuck Close
————————————————————————————————————————————————————————————
P024500
Measured voltage below limit
No Sub Type Information
Broken actuator, wire or ECM driver output
Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Wastegate Short Circuit Low
————————————————————————————————————————————————————————————
P024600
Measured voltage above limit
No Sub Type Information
Powerloss
Broken actuator, wire or ECM driver output
Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Wastegate Short Circuit High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P026200
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 1 Short Circuit High
————————————————————————————————————————————————————————————
P204300
No Sub Type Information
None
Urea tank temp sensor stuck high
Urea tank temp sensor
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor
Aftertreatment Reagent Tank Temperature Sensor Stuck
————————————————————————————————————————————————————————————
P209F73
Actuator Stuck Closed
None
Urea tank temp sensor or Urea tank heating system Urea tank temp sensor, Urea tank heating system
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor, Urea tank heating system
Aftertreatment Reagent Tank Temperature
————————————————————————————————————————————————————————————
P20F400
No Sub Type Information
Too low urea consumption
Urea level sensor stuck Clogged urea system Wrong urea tank Wrong dosing module Nozzle or
ACM Dosing module: dosing
valve
Diagnostic Service 14. No additional action is needed
Check:
Nozzle or
ACM Dosing module: dosing valve
AdBlue Consumption Too Low
————————————————————————————————————————————————————————————
U029D00
Lost communication with the node
No Sub Type Information
MS from Nox-sensor ECU Nox-sensor power supply CAN communication between ECM and Nox-EUC
Diagnostic Service 14. No additional action is needed
Check:
Nox-sensor power supply
CAN communication between ECM and Nox-EUC
Lost Communication With NOx Sensor “A”
————————————————————————————————————————————————————————————
P204C00
Measured voltage below limit
No Sub Type Information
No urea dosing
ACM Pump module: AdBlue pressure sensor
ACM Pump module: Internal cabling
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Diagnostic Service 14. No additional action is needed
Check:
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Aftertreatment Reagent Pressure Sensor Circuit Low
————————————————————————————————————————————————————————————
U016700
No Sub Type Information
The engine can not be started
Immobilizer unit not installed. (When Immo in Cluster is used, the Cluster maybe did not wake up properly)
Immo system
Diagnostic Service 14. No additional action is needed
Check:
Immo system
Lost Communication With Vehicle Immobilizer Control Module
————————————————————————————————————————————————————————————
P220A1C
Circuit Voltage Out of Range
Too high voltage to NOx- sensor ECU
Battery voltage
Diagnostic Service 14. No additional action is needed
Check:
Battery voltage
NOx Sensor Supply Voltage Circuit (Bank 1
Sensor 1)
————————————————————————————————————————————————————————————
U042600
No Sub Type Information
The engine can not be started
ECM and Immobilizer(or Cluster) unit security codes do not match.
Immo system
Diagnostic Service 14. No additional action is needed
Check:
Immo system
Invalid Data Received From Vehicle Immobilizer Control Module
————————————————————————————————————————————————————————————
P114000
No Sub Type Information
No VCB
low engine oil temperature
.
Diagnostic Service 14. No additional action is needed
Check:
low engine oil temperature
Volvo Compression Brake
(VCB) Control Oil Temperature Too Low
————————————————————————————————————————————————————————————
P113700
DUMMY fault. Not intented for fault
tracing
No Sub Type Information
DUMMY fault. Not intented for fault tracing
DUMMY fault. Not intented for fault tracing
DUMMY fault. Not intented for fault tracing
Check:
DUMMY fault. Not intented for fault tracing
Oil Thermostat
————————————————————————————————————————————————————————————
P113711
Measured voltage below limit
Circuit Short To Ground
Oil thermostat alwaysclosed.
Broken actuator, wire or
ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Oil Thermostat
————————————————————————————————————————————————————————————
P113712
Measured voltage above limit
Circuit Short To Battery
Oil thermostat always open. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Oil Thermostat
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P113713
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil thermostat always open. Increased fuel consumption may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Oil Thermostat
————————————————————————————————————————————————————————————
P011164
Signal Plausibility Failure
None
The boost temperature sensor output is showing either too high or to low value.
(abnormal value) Harness
Sensor
Ambient air temperature sensor.
Diagnostic Service 14. No additional action is needed
Check:
Harness Sensor
Ambient air temperature sensor.
Intake Air Temperature Sensor 1 Circuit Range/Performance Bank 1
————————————————————————————————————————————————————————————
P20E892
Performance or Incorrect Operation
No urea dosing
ACM dosing module: Dosing valve leakage.
Bleed orifice leakage, pressure hose lekage, pump internal leakage, empty ureatank
Tank frozen.
if pump/tank-lines are mixed-up when connecting them to the pump unit there will be no pressure built (check color mar Empty Urea tank, Urea filter clogged, Urea inlet pipe leakage/blocked, Urea tank ventilation, ACM Pump module: Pump
Diagnostic Service 14. No additional action is needed
Check:
Empty Urea tank, Urea filter clogged, Urea inlet pipe leakage/blocked, Urea tank ventilation, ACM Pump module: Pump
Reductant Pressure Too Low
————————————————————————————————————————————————————————————
P21CA00
No Sub Type Information
No dozing
Voltage supply to ACM. Voltage supply to Urea pump.
Diagnostic Service 14. No additional action is needed
Check:
Voltage supply to Urea pump.
Reductant Control Module Supply Voltage
————————————————————————————————————————————————————————————
P114411
Measured voltage below limit
Circuit Short To Ground
EMS can not control starter
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P114412
Measured voltage
above limit
Circuit Short To Battery
Impossible to activate
starter motor.
Start relay/harness
Diagnostic Service 14. No additional
action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P114413
Measured voltage outside the limits specified by the
sensor
Circuit Open
Impossible to activate starter motor
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P116A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
No urea dosing
.
Diagnostic Service 14. No additional action is needed
.
Reductant Pump “A” Control Low Side
————————————————————————————————————————————————————————————
P116B00
Measured voltage below limit
No Sub Type Information
No urea dosing
.
Diagnostic Service 14. No additional action is needed
.
Reductant Pump “A” Control Low Side Circuit
Low
————————————————————————————————————————————————————————————
P116C00
Measured voltage above limit
No Sub Type Information
No urea dosing
.
Diagnostic Service 14. No additional action is needed
.
Reductant Pump “A”
Control Low Side Circuit High
————————————————————————————————————————————————————————————
P021900
No Sub Type Information
Engine speed is limited (to commonly 1200rpm). VCB and EPD activated to lower espd below deactivation limit (commonly 1000rpm).
Engine is/was overspeeding. Engine could be running on oil, due to e.g. faulty crankcase oil filter.
Diagnostic Service 14. No additional action is needed
Check:
Engine could be running on oil, due to e.g. faulty crankcase oil filter.
Engine Overspeed Condition
————————————————————————————————————————————————————————————
P115C00
Measured voltage above limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power
Supply “C” Circuit High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P115D00
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power
Supply “C” Circuit Low
————————————————————————————————————————————————————————————
P06E970
Actuator Stuck On
The starter motor is deactivated
The starter motor is deactivated due to that the cogwheels of the starter and engine are stuck
None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to that the cogwheels of the starter and engine are stuck
Engine Starter Performance
————————————————————————————————————————————————————————————
P06E998
Component or System Over Temperature
The starter motor is deactivated
The starter motor is deactivated due to overheat None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to overheat
Engine Starter Performance
————————————————————————————————————————————————————————————
P115E97
Component or System Operation Obstructed or Blocked
No dozing
Bleed orifice clogged
Bleed orifice, Urea pressure sensor,
Diagnostic Service 14. No additional action is needed
Check:
Bleed orifice, Urea pressure sensor,
Reductant Return No Flow Detected
————————————————————————————————————————————————————————————
P11609B
High/Excessive Flow
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Root Cause Unknown (First Level)
————————————————————————————————————————————————————————————
P116192
Performance or Incorrect Operation
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Insufficient Reagent Quality (First Level)
————————————————————————————————————————————————————————————
P116300
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – NOx Control Monitoring System (First Level)
————————————————————————————————————————————————————————————
P26047F
Measured voltage below limit
Actuator Stuck Off
Preheat relay problem or sense SC-.
Shorting wire may break when attempt
Preheat sense 1
Preheat relay
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1 Preheat relay
Intake Air Heater “A” Circuit Range/Performance
————————————————————————————————————————————————————————————
P115600
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power Supply “A” Circuit High
————————————————————————————————————————————————————————————
P115700
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power Supply “A” Circuit Low
————————————————————————————————————————————————————————————
P115800
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Reductant Control Module Sensor Power Supply “B” Circuit High
————————————————————————————————————————————————————————————
P115900
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Reductant Control Module Sensor Power Supply “B” Circuit Low
————————————————————————————————————————————————————————————
P115A00
No Sub Type Information
Possible incread risk of crystalization
Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
Exhaust Gas Temperature Sensor Circuit Signal Compare Failure Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P115B00
No Sub Type Information
None
The sensor is stuck Leakage in exhaust system Leakage in intake system Sensor
Diagnostic Service 14. No additional action is needed
Check:
Leakage in exhaust system Leakage in intake system Sensor
Exhaust Gas Temperature Sensor Circuit Stuck Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P116441
General Checksum Failure
All ACM functionality disabled, no urea dosing
No software in ACM
.
Diagnostic Service 14. No additional action is needed
Check:
No software in ACM
Reductant Control Module Internal Control Module Memory Checksum Error
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P116500
No Sub Type Information
Buzzer signal (alert), Display of the message, with bip, simultaneously with the gear engaged pictogram.
Driver is at low speed but still shifts to high gear, range high.
Protective measure for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective measure for clutch/transmission
Driver Selected Too High Gear
————————————————————————————————————————————————————————————
P116600
No Sub Type Information
Buzzer signal (alert), Display of the message, with bip, simultaneously with the gear engaged pictogram.
Driver is at high speed but still down-shift to low gear, range low.
Protective measure for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective measure for clutch/transmission
Driver Selected Too Low Gear
————————————————————————————————————————————————————————————
P116700
No Sub Type Information
The starter motor is deactivated
The starter motor is deactivated due to that the PTO switch is active.
None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to that the PTO switch is active.
Starter Activated When PTO Is Active
————————————————————————————————————————————————————————————
P000041
General Checksum
Failure
The engine can not be
started
.
Diagnostic Service 14. No additional
action is needed
.
Control Module
————————————————————————————————————————————————————————————
P24FF00
No Sub Type Information
If tank temp is too high, no urea dosing
Urea tank temp is too high Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
Reductant Temperature Too High
————————————————————————————————————————————————————————————
U1FFF68
Event Information
None
None
Diagnostic Service 14. No additional action is needed
.
Factory Mode Active
————————————————————————————————————————————————————————————
P117A00
No Sub Type Information
Possible ammonia smell
SCR catalyst removed, Regent out of specification, Clogged dosing system Urea specification
Dosing system Catalyst deactivated
Diagnostic Service 14. No additional action is needed
Check:
Urea specification Dosing system Catalyst deactivated
SCR NOx Catalyst Efficiency Critically Below Threshold Bank 1
————————————————————————————————————————————————————————————
P047800
Measured voltage
above limit
No Sub Type
Information
Powerloss, engine break is
reduced
Broken actuator/Harness
AVU
Diagnostic Service 14. No additional
action is needed
Check:
AVU
Exhaust Pressure Control
Valve “A” High
————————————————————————————————————————————————————————————
P047700
Measured voltage
below limit
No Sub Type
Information
Powerloss, engine break is
reduced
Broken actuator/Harness
AVU
Diagnostic Service 14. No additional
action is needed
Check:
AVU
Exhaust Pressure Control
Valve “A” Low
————————————————————————————————————————————————————————————
P047513
Measured voltage outside the limits specified by the sensor
Circuit Open
Powerloss, engine break is reduced
Broken actuator/Harness AVU
Diagnostic Service 14. No additional action is needed
Check: AVU
Exhaust Pressure Control Valve “A”
————————————————————————————————————————————————————————————
P222764
Signal Plausibility Failure
Powerloss (minor) P3524:
Black smoke (minor)
The ambient air pressure is showing either too high or to low value.
(abnormal value) Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor ECM
Barometric Pressure Sensor “A” Circuit Range/Performance
————————————————————————————————————————————————————————————
P011513
Measured voltage outside the limits specified by the sensor
Circuit Open
Engine is difficult to start. Idle run regulation is detoriated.
Harness Sensor
Sensor/Harness
Diagnostic Service 14. No additional action is needed
Check: Sensor/Harness
Engine Coolant Temperature Sensor 1
————————————————————————————————————————————————————————————
P205E1F
Circuit Intermittent
Urea tank temp sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor, Cables, Connectors
Reductant Tank Temperature Sensor Circuit
Intermittent/Erratic
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P053E00
No Sub Type Information
Forced idle Engine shut down
The non-filtered pressure difference (between crankcase pressure and ambient air pressure) is/was above limit. (The fault code will remain during the entire driving cycle (unless reset).)
E.g. Blow-by at piston ring. NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Diagnostic Service 14. No additional action is needed
Check:
E.g. Blow-by at piston ring.
NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Crankcase Pressure Too High
————————————————————————————————————————————————————————————
P25AB00
Measured voltage
above limit
No Sub Type
Information
Possible black smoke during
start.
Harness/Broken actuator
Harness/Valve
Diagnostic Service 14. No additional
action is needed
Check:
Harness/Valve
Piston Cooling Oil Control
Circuit High
————————————————————————————————————————————————————————————
P25AA00
Measured voltage below limit
No Sub Type Information
No piston cooling=>major engine damage if high
loads.
Harness/Broken actuator Harness/Valve
Diagnostic Service 14. No additional action is needed
Check: Harness/Valve
Piston Cooling Oil Control Circuit Low
————————————————————————————————————————————————————————————
P010513
Measured voltage outside the limits specified by the sensor
Circuit Open
Powerloss
Connectors. Harness. Sensor
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Manifold Absolute Pressure/Barometric Pressure Sensor
————————————————————————————————————————————————————————————
P010800
Measured voltage above limit
No Sub Type Information
Powerloss
Connectors. Harness. Sensor
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Manifold Absolute Pressure/Barometric Pressure Sensor Circuit High
————————————————————————————————————————————————————————————
P010662
Signal Compare Failure
Powerloss Black smoke
The boost pressure sensor output is showing either too high or to low value.
(abnormal value) Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance
————————————————————————————————————————————————————————————
P25AE00
No Sub Type
Information
.
Diagnostic Service 14. No additional
action is needed
.
Piston Cooling Oil
Pressure Too Low
————————————————————————————————————————————————————————————
P25A900
DUMMY fault. Not intented for fault tracing
No Sub Type Information
DUMMY fault. Not intented for fault tracing
DUMMY fault. Not intented for fault tracing
DUMMY fault. Not intented for fault tracing
Check:
DUMMY fault. Not intented for fault tracing
Piston Cooling Oil Control
————————————————————————————————————————————————————————————
P25A913
Measured voltage outside the limits specified by the sensor
Circuit Open
Possible black smoke during start.
Harness/Broken actuator Harness/Valve
Diagnostic Service 14. No additional action is needed
Check: Harness/Valve
Piston Cooling Oil Control
————————————————————————————————————————————————————————————
P054070
Measured voltage above limit
Actuator Stuck On
Fuse for shorting wire breaks.
Sense wire SC+ or preheat relay broken
Preheat sense 1
Preheat relay
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1 Preheat relay
Intake Air Heater “A” Control
————————————————————————————————————————————————————————————
P225D00
No Sub Type Information
None except fault code and lamp
Sensor removed (measures surround air)
Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
NOx Sensor Performance – Signal Stuck Low Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P10F200
Measured voltage below limit
No Sub Type Information
None
Pressure switch / Harness Pressure switch/Harness
Diagnostic Service 14. No additional action is needed
Check:
Pressure switch/Harness
Air Filter Indicator Circuit Low
————————————————————————————————————————————————————————————
P10F300
Measured voltage
above limit
No Sub Type
Information
None
Harness
Diagnostic Service 14. No additional
action is needed
Check:
Harness
Air Filter Indicator Circuit
High
————————————————————————————————————————————————————————————
P22FB00
No Sub Type Information
Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
NOx Sensor Performance – Sensing Element Bank 1 Sensor 1
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P110F90
Stuck On
Stop switch can not be
activated
Switch
Engine stop switch
Diagnostic Service 14. No additional
action is needed
Check:
Engine stop switch
Engine Stop Switch Stuck
————————————————————————————————————————————————————————————
P110400
No Sub Type Information
The engine can not be started
Bad software configuration Software download application
Diagnostic Service 14. No additional action is needed
Check:
Software download application
Factory Mode
————————————————————————————————————————————————————————————
P10F824
Signal Stuck High
.
Diagnostic Service 14. No additional action is needed
.
Air Filter Clogged
————————————————————————————————————————————————————————————
P055A00
DUMMY fault. Not intented for fault
tracing
No Sub Type Information
DUMMY fault. Not intented for fault tracing
DUMMY fault. Not intented for fault tracing
DUMMY fault. Not intented for fault tracing
Check:
DUMMY fault. Not intented for fault tracing
Engine Oil Pressure Sensor/Switch “B”
————————————————————————————————————————————————————————————
P055A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
.
Diagnostic Service 14. No additional action is needed
.
Engine Oil Pressure Sensor/Switch “B”
————————————————————————————————————————————————————————————
P055B64
Signal Plausibility Failure
The control function closes the PCJ valve. When the fault is set, the PCJ oil pressure is forced to max (if calibrated so in the pcj_ function).
The sensor is stuck, has an offset or another kind of rationality fault. It could also be the valve that cannot be closed.
Sensor/Valve
Diagnostic Service 14. No additional action is needed
Check: Sensor/Valve
Piston Cooling Oil Pressure Sensor Range/Performance
————————————————————————————————————————————————————————————
P055D00
Measured voltage above limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Piston Cooling Oil Pressure Sensor Circuit High
————————————————————————————————————————————————————————————
P112800
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Piston Cooling Oil Pressure Moderately Low
————————————————————————————————————————————————————————————
P029800
No Sub Type Information
Powerloss
Extreme driving conditions Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Engine Oil Over Temperature
————————————————————————————————————————————————————————————
P111600
No Sub Type Information
Intermittent Powerloss
VGT stuck, Wastegate stuck VGT Turbo, Wastegate
Diagnostic Service 14. No additional action is needed
Check:
VGT Turbo, Wastegate
Manifold Absolute
Pressure Moderately Too High
————————————————————————————————————————————————————————————
P111800
No Sub Type Information
Intermittent Powerloss
VGT stuck, Wastegate stuck VGT Turbo, Wastegate
Diagnostic Service 14. No additional action is needed
Check:
VGT Turbo, Wastegate
Manifold Absolute Pressure Too High
————————————————————————————————————————————————————————————
P111D00
No Sub Type
Information
.
Diagnostic Service 14. No additional
action is needed
.
Engine Coolant Level
Moderately Low
————————————————————————————————————————————————————————————
P111E00
No Sub Type Information
Powerloss
Extreme Driving conditions
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Engine Coolant Temperature Moderately High
————————————————————————————————————————————————————————————
P112500
No Sub Type Information
Powerloss
Extreme driving conditions Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Fan
Oil thermostat Coolant system Clogged oil cooler
Engine Oil Temperature Moderately High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U117888
It has not been possible to send frames on Vehicle Communication Powertrain CAN and It has not been possible to receive frames on Vehicle Communication Powertrain CAN
Bus off
.
Diagnostic Service 14. No additional action is needed
.
Vehicle Communication Powertrain CAN
————————————————————————————————————————————————————————————
P253913
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Low Pressure Fuel System Sensor Circuit
————————————————————————————————————————————————————————————
P254200
Measured voltage above limit
No Sub Type Information
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Low Pressure Fuel System Sensor Circuit High
————————————————————————————————————————————————————————————
P008A00
No Sub Type Information
Fuel injection can be affected.
High differential pressure over filter.
Leakage Filter
Sensor
Diagnostic Service 14. No additional action is needed
Check: Filter Sensor
Low Pressure Fuel System Pressure – Too Low
————————————————————————————————————————————————————————————
P113500
No Sub Type Information
Engine speed is limited (to commonly 1200rpm). VCB and EPG activated to lower espd below deactivation limit (commonly 1000rpm).
The non-filtered pressure difference (between crankcase pressure and ambient air pressure) is/was above limit. (The fault code will remain during the entire driving cycle (unless reset).)
E.g. Blow-by at piston ring. NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Diagnostic Service 14. No additional action is needed
Check:
E.g. Blow-by at piston ring.
NOT Crankcase pressure sensor or ambient air pressure sensor!!!
Crankcase Pressure Relative To Ambient Pressure Too High
————————————————————————————————————————————————————————————
P047F71
Actuator Stuck
Decreased brake power.
sensor, Closed loop butterfly
sensor, butterfly
Diagnostic Service 14. No additional action is needed
Check:
sensor, butterfly
Exhaust Pressure Control Valve “A” Stuck Open
————————————————————————————————————————————————————————————
U000188
It has not been possible to send frames on High Speed CAN Communication Bus and It has not been possible to receive frames on High Speed CAN Communication Bus
Bus off
.
Diagnostic Service 14. No additional action is needed
.
CAN Communication Backbone 2 Net
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U001088
It has not been possible to send frames on Medium Speed CAN Communication Bus and It has not been possible to receive frames on Medium Speed CAN Communication Bus
Bus off
.
Diagnostic Service 14. No additional action is needed
.
CAN Communication Backbone 1 Net
————————————————————————————————————————————————————————————
U010187
Missing Message
ETC2 not responding
.
Diagnostic Service 14. No additional
action is needed
Check:
ETC2 not responding
Lost Communication with
TECU
————————————————————————————————————————————————————————————
P034031
No Signal
The engine start time will increase.
Possible loss of power
Sensor/Harness Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Camshaft Position Sensor “A” Bank 1 or Single Sensor
————————————————————————————————————————————————————————————
P034138
Signal Frequency Incorrect
The engine start time will increase.
Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Camshaft Position Sensor A Circuit Range/Performance
————————————————————————————————————————————————————————————
P052612
Measured voltage above limit
Circuit Short To Battery
Either
1. Fan will work as on/off fan. 100% fan speed if cooling is needed. Higher fuel consumption.
Or
2. Fan will work in open loop mode. Deteriorated fan control, but might not be noticable to driver.
Broken sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Fan Speed Sensor Circuit
————————————————————————————————————————————————————————————
P054300
Measured voltage outside the limits specified by the
sensor
No Sub Type Information
Might get start problems in cold climate.
Heating element or wire broken.
Preheat sense 1
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1
Intake Air Heater A Circuit Open
————————————————————————————————————————————————————————————
P001676
Wrong Mounting Position
Fuel consumption increased
Bad correlation between cam and crank, engine transmission not correct
Engine transmission
Diagnostic Service 14. No additional action is needed
Check:
Engine transmission
Crankshaft Position – Camshaft Position Correlation
————————————————————————————————————————————————————————————
P007100
No Sub Type Information
Ambient air temp sensor or boost temp sensor faulty Ambient air temp sensor or Boost temp sensor
Diagnostic Service 14. No additional action is needed
Check:
Ambient air temp sensor or Boost temp sensor
Ambient Air Temperature Sensor Range/Performance
————————————————————————————————————————————————————————————
P02CD00
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 1 Fuel Injector Offset Learning at Max Limit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P02CF00
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 2 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D100
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 3 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D300
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 4 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P02D500
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 5 Fuel Injector Offset Learning at Max Limit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P02D700
No Sub Type Information
Larger errors can be noticeable at engine idle speed
– PTO is connected incorrectly so that ECM is not informed if it is engaged.
– Low or high flow injector.
– Uneven spaced tooth on flywheel.
– Bad compression.
Injector, see Probable errors
Diagnostic Service 14. No additional action is needed
Check:
Injector, see Probable errors
Cylinder 6 Fuel Injector Offset Learning at Max Limit
————————————————————————————————————————————————————————————
P033531
No Signal
Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running. Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankshaft Position Sensor “A”
————————————————————————————————————————————————————————————
P033638
Signal Frequency Incorrect
Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running. Possible loss of power
Sensor monting Sensor/Lack of shims
Diagnostic Service 14. No additional action is needed
Check:
Sensor/Lack of shims
Crankshaft Position Sensor A Circuit Range/Performance
————————————————————————————————————————————————————————————
P033900
No Sub Type Information
The engine start time will increase.Engine is running with imprecise timing causing risk of high fuel consumption and smoke. Cylinder balancing not working with risk of uneven running.
Possible loss of power
Harness/sensor monting Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankshaft Position Sensor A Circuit Intermittent
————————————————————————————————————————————————————————————
P203F00
No Sub Type Information
No urea dosing
Urea symbol in cluster
Tank almost empty, stop dosing to maintain cooling ECM interpretation of raw value. Urea level. DST problem.
Diagnostic Service 14. No additional action is needed
Check:
ECM interpretation of raw value. Urea level. DST problem.
Reductant Level Low
————————————————————————————————————————————————————————————
P205A13
Measured voltage outside the limits specified by the sensor
Circuit Open
None
AdBlue tank temp sensor Cables
Connectors
Urea tank temp sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor, Cables, Connectors
Reductant Tank Temperature Sensor
————————————————————————————————————————————————————————————
P208064
Signal Plausibility Failure
None
The sensor is not plausible Leakage in exhaust system Leakage in intake system Sensor
Diagnostic Service 14. No additional action is needed
Check:
Leakage in exhaust system Leakage in intake system Sensor
Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P220013
Measured voltage outside the limits specified by the sensor
Circuit Open
Cabling between Nox- sensor and Nox-sensor ECU Nox-sensor
Nox-sensor cabling Nox-sensor
Diagnostic Service 14. No additional action is needed
Check:
Nox-sensor cabling Nox-sensor
NOx Sensor Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P220164
Signal Plausibility Failure
Excessive urea dosing (only for SCR system)
Exhaust system leakage Air intake leakage
Nox-sensor
Dosing system (only for SCR system)
Exhaust system Air intake system
Nox-sensor
Diagnostic Service 14. No additional action is needed
Check:
Dosing system (only for SCR system) Exhaust system
Air intake system Nox-sensor
NOx Sensor Circuit Range/Performance
————————————————————————————————————————————————————————————
P060100
No Sub Type Information
Engine derate
signature failure
.
Diagnostic Service 14. No additional action is needed
Check: signature failure
Internal Control Module Memory Check Sum Error
————————————————————————————————————————————————————————————
P060700
No Sub Type
Information
Not possible to reprogram
ECU
.
Diagnostic Service 14. No additional
action is needed
.
Control Module
Performance
————————————————————————————————————————————————————————————
P06151C
Measured voltage outside the limits specified by the
sensor
Circuit Voltage Out of Range
Impossible to activate starter motor
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay
————————————————————————————————————————————————————————————
P061600
Measured voltage below limit
No Sub Type Information
EMS can not control starter
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Circuit Low
————————————————————————————————————————————————————————————
P061700
Measured voltage
above limit
No Sub Type
Information
Impossible to activate
starter motor.
Start relay/harness
Diagnostic Service 14. No additional
action is needed
Check:
Start relay/Harness
Starter Relay Circuit High
————————————————————————————————————————————————————————————
P066800
Measured voltage below limit
No Sub Type Information
None
Internal fault in ECM ECM
Diagnostic Service 14. No additional action is needed
Check: ECM
PCM/ECM/TCM Internal Temperature Sensor
Circuit Low
————————————————————————————————————————————————————————————
P06B100
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply A Circuit Low
————————————————————————————————————————————————————————————
P06B200
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply A Circuit High
————————————————————————————————————————————————————————————
P06B400
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply B Circuit Low
————————————————————————————————————————————————————————————
P06B500
No Sub Type Information
Incorrect sensor readings
Harness/Sensor power supply
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor Power Supply B Circuit High
————————————————————————————————————————————————————————————
P20EE00
No Sub Type Information
NOx-conversion reduced by appr. 50%
Possible ammonia smell
Regent out of specification, Dosing performance low Urea specification
Dosing system
Diagnostic Service 14. No additional action is needed
Check:
Urea specification Dosing system
SCR NOx Catalyst Efficiency Below Threshold (Bank 1)
————————————————————————————————————————————————————————————
P260013
Measured voltage outside the limits specified by the
sensor
Circuit Open
Pump always at half speed. High coolant temperatures may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Coolant Pump Control Circuit/Open
————————————————————————————————————————————————————————————
P260200
Measured voltage below limit
No Sub Type Information
Pump always runs at full speed. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Coolant Pump Control Circuit Low
————————————————————————————————————————————————————————————
P260300
Measured voltage above limit
No Sub Type Information
Pump always at half speed. High coolant temperatures may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Coolant Pump Control Circuit High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P261087
Missing Message
Timestamps from Cluster not available
J1708 time data failure and J1939 message does not exist. (Cluster error).
Cluster
Diagnostic Service 14. No additional action is needed
Check: Cluster
ECM/PCM Internal Engine Off Timer Performance
————————————————————————————————————————————————————————————
P2BA700
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Empty Reagent Tank
————————————————————————————————————————————————————————————
P023400
No Sub Type Information
Too high pressure Turbine , Compressor
Diagnostic Service 14. No additional action is needed
Check:
Turbine , Compressor
Turbocharger/Supercharg er Overboost Condition
————————————————————————————————————————————————————————————
P029900
No Sub Type Information
Too low pressure
Boost leakage, wastegate, VGT, compressor.
Diagnostic Service 14. No additional action is needed
Check:
Boost leakage, wastegate, VGT, compressor.
Turbocharger/Supercharg er Underboost
————————————————————————————————————————————————————————————
U300001
Measured voltage outside the limits specified by the sensor
General Electrical Failure
Possible damage on EMS system components depending on the high voltage (>36V)
Generator, external charger
Diagnostic Service 14. No additional action is needed
Check:
Generator, external charger
Electronic control unit
————————————————————————————————————————————————————————————
U300041
Program memory corruption
General Checksum Failure
The engine can not be started
No software Software download
application
Diagnostic Service 14. No additional action is needed
Check:
Software download application
Electronic control unit
————————————————————————————————————————————————————————————
P007087
Missing Message
None
J1708 and CAN ambient air temperature message does not exist.
Harness. Cluster
Diagnostic Service 14. No additional action is needed
Check:
Harness. Cluster
Ambient Air Temperature Sensor “A”
————————————————————————————————————————————————————————————
P011013
Measured voltage outside the limits specified by the
sensor
Circuit Open
Engine is running but could be difficult to start in cold climate.
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Intake Air Temperature Sensor 1 Bank 1
————————————————————————————————————————————————————————————
P011200
Measured voltage below limit
No Sub Type Information
Engine is running but could be difficult to start in cold climate.
Connectors. Harness.
Sensor
Diagnostic Service 14. No additional action is needed
Check: Connectors. Harness.
Sensor
Intake Air Temperature Sensor 1 Circuit Low Bank 1
————————————————————————————————————————————————————————————
P011700
Measured voltage below limit
No Sub Type Information
Engine is difficult to start. Idle run regulation is
detoriated.
Harness Sensor
Sensor/Harness
Diagnostic Service 14. No additional action is needed
Check: Sensor/Harness
Engine Coolant Temperature Circuit Low
————————————————————————————————————————————————————————————
P021700
No Sub Type Information
Powerloss
Extreme Driving conditions Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Diagnostic Service 14. No additional action is needed
Check:
Extreme driving conditions Coolant thermostat
Fan
Blocked radiator
Engine Coolant Over Temperature Condition
————————————————————————————————————————————————————————————
P047013
Measured voltage outside the limits specified by the
sensor
Circuit Open
Open loop control enabled. Decreased brake power.
.
Diagnostic Service 14. No additional action is needed
.
Exhaust Pressure Sensor “A”
————————————————————————————————————————————————————————————
P047164
Signal Plausibility Failure
Open loop control enabled. Decreased brake power.
sensor, Closed loop butterfly, AVU sensor, butterfly, AVU
Diagnostic Service 14. No additional action is needed
Check:
sensor, butterfly, AVU
Engine Exhaust Back Pressure Circuit Range/Performance
————————————————————————————————————————————————————————————
P047300
Measured voltage above limit
No Sub Type Information
Open loop control enabled. Decreased brake power.
.
Diagnostic Service 14. No additional action is needed
.
Engine Exhaust Back Pressure Circuit High
————————————————————————————————————————————————————————————
P048013
Measured voltage outside the limits specified by the sensor
Circuit Open
Fan runs at full speed. Increased fuel consumption may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P051B64
Signal Plausibility Failure
Powerloss (minor) P3524:
Black smoke (minor)
The crank case pressure is showing either too high or to low value.
(abnormal value) Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor ECM
Engine High Resolution Crankcase Pressure Circuit Range/Performance
————————————————————————————————————————————————————————————
P051A13
Measured voltage outside the limits specified by the sensor
Circuit Open
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Crankcase Pressure Sensor
————————————————————————————————————————————————————————————
P051D00
Measured voltage above limit
No Sub Type Information
None
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Engine High Resolution Crankcase Pressure
————————————————————————————————————————————————————————————
P052300
Measured voltage above limit
No Sub Type Information
Oil pressure shows 0 in the cluster. Engine is running.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Engine Oil Pressure Circuit High
————————————————————————————————————————————————————————————
P052400
No Sub Type Information
Low pressure, powerloss
Oil leakage, broken oil pump, clogged oil system Oil system
Diagnostic Service 14. No additional action is needed
Check:
Oil system
Engine Oil Pressure Too Low
————————————————————————————————————————————————————————————
P222800
Measured voltage below limit
No Sub Type Information
None
Internal fault in ECM Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check: Sensor
ECM
Barometric Pressure Circuit Low
————————————————————————————————————————————————————————————
P222900
Measured voltage above limit
No Sub Type Information
None
Internal fault in ECM Sensor
ECM
Diagnostic Service 14. No additional action is needed
Check:
Sensor ECM
Barometric Pressure Circuit High
————————————————————————————————————————————————————————————
P226400
No Sub Type Information
None
No error: Used for indication
when priming pump is active
None
Diagnostic Service 14. No additional action is needed
Check:
No error: Used for indication when priming pump is active
Water in Fuel Sensor
————————————————————————————————————————————————————————————
P226600
Measured voltage
below limit
No Sub Type
Information
Will give water in fuel
indication.
Harness
Diagnostic Service 14. No additional
action is needed
Check:
Harness
Water In Fuel Indicator
Circuit Low
————————————————————————————————————————————————————————————
P226700
Measured voltage above limit
No Sub Type Information
Undetected water in fuel can lead to engine stop
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Water In Fuel Indicator Circuit High
————————————————————————————————————————————————————————————
P250C00
Measured voltage below limit
No Sub Type Information
Oil level can not be measured.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check:
Harness Sensor
Engine Oil Level Circuit Low
————————————————————————————————————————————————————————————
P250F00
No Sub Type Information
None
Critically low oil level Leakage
Leakage
Sensor
Diagnostic Service 14. No additional action is needed
Check: Leakage Sensor
Engine Oil Level Too Low
————————————————————————————————————————————————————————————
P255613
Measured voltage outside the limits specified by the
sensor
Circuit Open
Coolant level can not be detected.
Harness Harness connector
sensor
Diagnostic Service 14. No additional action is needed
Check: Harness connector
sensor
Engine Coolant Level Sensor/Switch
————————————————————————————————————————————————————————————
P255900
Measured voltage above limit
No Sub Type Information
Coolant level can not be detected.
Harness Harness connector
sensor
Diagnostic Service 14. No additional action is needed
Check: Harness connector
sensor
Engine Coolant Level Circuit High
————————————————————————————————————————————————————————————
P256000
No Sub Type Information
Powerloss
Coolant level below range if not Harness
Coolant system
Diagnostic Service 14. No additional action is needed
Check:
Coolant system
Engine Coolant Level Low
————————————————————————————————————————————————————————————
P108600
No Sub Type Information
None
Low oil level Leakage Leakage
Sensor
Diagnostic Service 14. No additional action is needed
Check: Leakage Sensor
Oil Level Moderately Low
————————————————————————————————————————————————————————————
P20BF00
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Reagent Hose Heater 2 Short Circuit Low
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U014100
Lost communication with the node on Medium Speed CAN Communication Bus
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With VMCU
————————————————————————————————————————————————————————————
U012A87
Lost communication with the node
Missing Message
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With CCIOM
————————————————————————————————————————————————————————————
P109000
No Sub Type Information
Display of the message, without bip, simultaneously with the gear engaged
pictogram
Driver started at too high gear at start
Protective alert for
clutch/transmission
Diagnostic Service 14. No additional action is needed
Check:
Protective alert for clutch/transmission
Transmission High Gear At Start
————————————————————————————————————————————————————————————
P208E00
No Sub Type Information
No urea dosing
Sensor/Harness dosing valve
injector, clogged hoses
Diagnostic Service 14. No additional action is needed
Check:
dosing valve
injector, clogged hoses
Aftertreatment Reagent Dosing Valve Clogged
————————————————————————————————————————————————————————————
P109541
General Checksum
Failure
Engine derate
.
Diagnostic Service 14. No additional
action is needed
.
Aftertreatment Control
Unit
————————————————————————————————————————————————————————————
P109641
General Checksum
Failure
Engine derate
.
Diagnostic Service 14. No additional
action is needed
.
Transmission Control Unit
————————————————————————————————————————————————————————————
P069200
Measured voltage above limit
No Sub Type Information
Fan runs at full speed. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit High
————————————————————————————————————————————————————————————
P069100
Measured voltage below limit
No Sub Type Information
Fan always deactivated or always activated if fault is intermittent.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Fan 1 Control Circuit Low
————————————————————————————————————————————————————————————
U015500
Lost communication with the node on Medium Speed CAN Communication Bus
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With Instrument Panel Cluster (IPC) Control Module
————————————————————————————————————————————————————————————
P052013
Measured voltage outside the limits specified by the sensor
Circuit Open
Oil pressure shows 0 in the cluster. Engine is running.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Pressure Sensor/Switch “A”
————————————————————————————————————————————————————————————
P066613
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Internal fault in ECM ECM
Diagnostic Service 14. No additional action is needed
Check: ECM
Control Module Internal Temperature Sensor “A”
————————————————————————————————————————————————————————————
P020113
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 1 Injector “A”
————————————————————————————————————————————————————————————
P020313
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 3 Injector “A”
————————————————————————————————————————————————————————————
P020413
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 4 Injector “A”
————————————————————————————————————————————————————————————
P020513
Measured voltage outside the limits specified by the sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 5 Injector “A”
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P020613
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 6 Injector “A”
————————————————————————————————————————————————————————————
P220E93
No Operation
Sensor
Diagnostic Service 14. No additional action is needed
Check: Sensor
NOx Sensor Heater Control Circuit Range/Performance (Bank
1 Sensor 1)
————————————————————————————————————————————————————————————
P250A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil level can not be measured.
Sensor/Harness Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Level Sensor
————————————————————————————————————————————————————————————
P020213
Measured voltage outside the limits specified by the
sensor
Circuit Open
Loss of power and uneven running. Run on three to five cylinders
Harness/Broken solenoid Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Cylinder 2 Injector “A”
————————————————————————————————————————————————————————————
P100E18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 2
————————————————————————————————————————————————————————————
P100F18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 3
————————————————————————————————————————————————————————————
P101018
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 4
————————————————————————————————————————————————————————————
P101518
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 5
————————————————————————————————————————————————————————————
P101618
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 6
————————————————————————————————————————————————————————————
P101711
Measured voltage below limit
Circuit Short To Ground
High fuel consumption due to fuel leakage.
Broken solenoid, wire or ECM driver output
Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P101712
Measured voltage above limit
Circuit Short To Battery
Valve constantly shut.
Broken solenoid, wire or ECM driver output
Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P101713
Measured voltage outside the limits specified by the sensor
Circuit Open
Valve constantly shut.
Broken solenoid or wire. Water-in-fuel valve driver
Diagnostic Service 14. No additional action is needed
Check:
Water-in-fuel valve driver
Water In Fuel Drainage Valve
————————————————————————————————————————————————————————————
P220300
No Sub Type Information
Cabling between Nox- sensor and Nox-sensor ECU Nox-sensor
Nox-sensor cabling Nox-sensor
Diagnostic Service 14. No additional action is needed
Check:
Nox-sensor cabling Nox-sensor
NOx Sensor Circuit High Bank 1 Sensor 1
————————————————————————————————————————————————————————————
P2BA800
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Interruption of Reagent Dosing Activity
————————————————————————————————————————————————————————————
P2BA900
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Insufficient Reagent Quality
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P2BAA00
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Low Reagent Consumption
————————————————————————————————————————————————————————————
P2BAD00
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Root Cause Unknown
————————————————————————————————————————————————————————————
P2BAE96
Component Internal Failure
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – NOx Control Monitoring System
————————————————————————————————————————————————————————————
P100211
Measured voltage below limit
Circuit Short To Ground
Induction air is hot. Preheat relay is impossible to turn
off.
Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Preheat Relay
————————————————————————————————————————————————————————————
P100212
Measured voltage above limit
Circuit Short To Battery
Preheat relay not activated. White smoke for cold start. Start problems in cold climate.
Preheat relay solenoid shorted
Preheat relay.
Diagnostic Service 14. No additional action is needed
Check: Preheat relay.
Preheat Relay
————————————————————————————————————————————————————————————
P100213
Measured voltage outside the limits specified by the sensor
Circuit Open
Preheat relay not activated. White smoke for cold start. Start problems in cold climate.
Harness or Preheat relay solenoid
Harness. Preheat relay.
Diagnostic Service 14. No additional action is needed
Check:
Harness. Preheat relay.
Preheat Relay
————————————————————————————————————————————————————————————
P100629
Signal invalid
None
The boost temperature sensor output is showing constant value.
Harness
Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Intake Air Temperature Sensor 1 Stuck Bank 1
————————————————————————————————————————————————————————————
P100713
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Pressure switch / Harness Pressure switch/Harness
Diagnostic Service 14. No additional action is needed
Check:
Pressure switch/Harness
Air Filter Indicator
————————————————————————————————————————————————————————————
P100D18
Circuit Current Below Threshold
None
Injector/Harness resistance too high.
Injector/Harness
Diagnostic Service 14. No additional action is needed
Check: Injector/Harness
Injector 1
————————————————————————————————————————————————————————————
P102111
Measured voltage below limit
Circuit Short To Ground
VCB can not be turned off. Causes engine to stop.
Engine impossible to
restart.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
P102112
Measured voltage above limit
Circuit Short To Battery
VCB can not be turned on. Engine break function derated. Gear shift performance derated for some automatic transmission boxes.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
P102113
Measured voltage outside the limits specified by the sensor
Circuit Open
VCB can not be turned on. Engine break function derated. Gear shift performance derated for some automatic transmission boxes.
Broken actuator/Harness VCB actuator
Diagnostic Service 14. No additional action is needed
Check:
VCB actuator
Volvo Compression Brake (VCB) Control Circuit
————————————————————————————————————————————————————————————
U010E00
Lost communication with the node
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Lost Communication With Reductant Control
Module
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P019513
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness Sensor
Engine Oil Temperature Sensor “A”
————————————————————————————————————————————————————————————
P204A13
Measured voltage outside the limits specified by the sensor
Circuit Open
No urea dosing
ACM Pump module: AdBlue pressure sensor
ACM Pump module: Internal cabling
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Diagnostic Service 14. No additional action is needed
Check:
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Reductant Pressure Sensor
————————————————————————————————————————————————————————————
P203D00
Measured voltage above limit
No Sub Type Information
None
AdBlue tank level sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
AdBlue tank level sensor, Cables, Connectors
Aftertreatment Reagent Level Short Circuit High
————————————————————————————————————————————————————————————
P208A13
Measured voltage outside the limits specified by the sensor
Circuit Open
No urea dosing
Wiring harness internal error in pump
Diagnostic Service 14. No additional action is needed
Check:
Wiring harness internal error in pump
Reductant Pump “A” Control
————————————————————————————————————————————————————————————
P026500
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 2 Short Circuit High
————————————————————————————————————————————————————————————
P026800
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 3 Short Circuit High
————————————————————————————————————————————————————————————
P027100
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 4 Short Circuit High
————————————————————————————————————————————————————————————
P027400
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 5 Short Circuit High
————————————————————————————————————————————————————————————
P027700
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 6 Short Circuit High
————————————————————————————————————————————————————————————
P20B300
Measured voltage below limit
No Sub Type Information
None
.
Diagnostic Service 14. No additional action is needed
.
Reductant Heater Coolant Control Valve Circuit Low
————————————————————————————————————————————————————————————
P204800
Measured voltage below limit
No Sub Type Information
No urea dosing
ACM Pump module: DCU ACM Pump module: internal cabling
ACM Pump module: DCU,
ACM Pump module: internal cabling
Diagnostic Service 14. No additional action is needed
Check:
ACM Pump module: DCU, ACM Pump module: internal cabling
Aftertreatment Reagent Dosing Valve Short Circuit Low
————————————————————————————————————————————————————————————
P204713
Measured voltage outside the limits specified by the sensor
Circuit Open
no urea dosing
Cable / Connectors
ACM Dosing module: Dosing valve
Cable / Connectors ACM Dosing module: Dosing
valve
Diagnostic Service 14. No additional action is needed
Check:
Cable / Connectors ACM Dosing module: Dosing valve
Reductant Injection Valve Control Bank 1 Unit 1
————————————————————————————————————————————————————————————
P20C300
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Reagent Hose Heater 3 Short
Circuit Low
————————————————————————————————————————————————————————————
P20BB00
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Aftertreatment Reagent Hose Heater 1 Short
Circuit Low
————————————————————————————————————————————————————————————
P20A200
Measured voltage below limit
No Sub Type Information
Not possible to perform afterrun
Internal electrical failure in valve within the ACM
Diagnostic Service 14. No additional action is needed
Check:
Internal electrical failure in valve within the ACM
Aftertreatment Reagent Direction Valve Short
Circuit Low
————————————————————————————————————————————————————————————
P065900
Measured voltage above limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
ACM Actuator High Supply 1 Short Circuit
High
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P065800
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
ACM Actuator High Supply 1 Short Circuit Low
————————————————————————————————————————————————————————————
P208D00
Measured voltage above limit
No Sub Type Information
No urea dosing
Wiring harness internal error in pump
Diagnostic Service 14. No additional action is needed
Check:
Wiring harness internal error in pump
Aftertreatment Reagent
Pump Control Short Circut High
————————————————————————————————————————————————————————————
P208C00
Measured voltage below limit
No Sub Type Information
No urea dosing
Wiring harness internal error in pump
Diagnostic Service 14. No additional action is needed
Check:
Wiring harness internal error in pump
Aftertreatment Reagent Pump Control Short
Circuit Low
————————————————————————————————————————————————————————————
P203A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
None
AdBlue tank level sensor, Cables, Connectors
Diagnostic Service 14. No additional action is needed
Check:
AdBlue tank level sensor, Cables, Connectors
Reductant Level Sensor “A”
————————————————————————————————————————————————————————————
P019700
Measured voltage below limit
No Sub Type Information
None
Harness Sensor
Diagnostic Service 14. No additional action is needed
Check: Harness
Sensor
Oil Temperature Short Circuit Low
————————————————————————————————————————————————————————————
P024313
Measured voltage outside the limits specified by the
sensor
Circuit Open
Powerloss
Broken actuator or wire. Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Turbocharger/Supercharg er Wastegate Solenoid “A”
————————————————————————————————————————————————————————————
P024471
Actuator Stuck
Possible turbo damage
Wategate mechanically damaged
Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Wastegate Stuck Close
————————————————————————————————————————————————————————————
P024500
Measured voltage below limit
No Sub Type Information
Broken actuator, wire or
ECM driver output Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Wastegate Short Circuit Low
————————————————————————————————————————————————————————————
P024600
Measured voltage above limit
No Sub Type Information
Powerloss
Broken actuator, wire or ECM driver output
Wastegate
Diagnostic Service 14. No additional action is needed
Check: Wastegate
Wastegate Short Circuit High
————————————————————————————————————————————————————————————
P026200
Measured voltage above limit
No Sub Type Information
Loss of power and uneven running. Run on three to
five cylinders
Harness shorted Harness
Diagnostic Service 14. No additional action is needed
Check: Harness
Injector 1 Short Circuit High
————————————————————————————————————————————————————————————
P204300
No Sub Type Information
None
Urea tank temp sensor stuck high
Urea tank temp sensor
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor
Aftertreatment Reagent Tank Temperature Sensor Stuck
————————————————————————————————————————————————————————————
P209F73
Actuator Stuck Closed
None
Urea tank temp sensor or Urea tank heating system Urea tank temp sensor, Urea tank heating system
Diagnostic Service 14. No additional action is needed
Check:
Urea tank temp sensor, Urea tank heating system
Aftertreatment Reagent Tank Temperature
————————————————————————————————————————————————————————————
P20F400
No Sub Type Information
Too low urea consumption
Urea level sensor stuck Clogged urea system Wrong urea tank Wrong dosing module Nozzle or
ACM Dosing module: dosing
valve
Diagnostic Service 14. No additional action is needed
Check:
Nozzle or
ACM Dosing module: dosing valve
AdBlue Consumption Too Low
————————————————————————————————————————————————————————————
U029D00
Lost communication with the node
No Sub Type Information
MS from Nox-sensor ECU Nox-sensor power supply CAN communication between ECM and Nox-EUC
Diagnostic Service 14. No additional action is needed
Check:
Nox-sensor power supply
CAN communication between ECM and Nox-EUC
Lost Communication With NOx Sensor “A”
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P204C00
Measured voltage below limit
No Sub Type Information
No urea dosing
ACM Pump module: AdBlue pressure sensor
ACM Pump module: Internal cabling
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Diagnostic Service 14. No additional action is needed
Check:
ACM Pump module: Urea pressure sensor, ACM Pump module: Internal cabling
Aftertreatment Reagent Pressure Sensor Circuit Low
————————————————————————————————————————————————————————————
U016700
No Sub Type Information
The engine can not be started
Immobilizer unit not installed. (When Immo in Cluster is used, the Cluster maybe did not wake up properly)
Immo system
Diagnostic Service 14. No additional action is needed
Check:
Immo system
Lost Communication With Vehicle Immobilizer Control Module
————————————————————————————————————————————————————————————
P220A1C
Circuit Voltage Out of Range
Too high voltage to NOx- sensor ECU
Battery voltage
Diagnostic Service 14. No additional action is needed
Check:
Battery voltage
NOx Sensor Supply Voltage Circuit (Bank 1
Sensor 1)
————————————————————————————————————————————————————————————
U042600
No Sub Type Information
The engine can not be started
ECM and Immobilizer(or Cluster) unit security codes do not match.
Immo system
Diagnostic Service 14. No additional action is needed
Check:
Immo system
Invalid Data Received From Vehicle Immobilizer Control Module
————————————————————————————————————————————————————————————
P114000
No Sub Type Information
No VCB
low engine oil temperature
.
Diagnostic Service 14. No additional action is needed
Check:
low engine oil temperature
Volvo Compression Brake (VCB) Control Oil
Temperature Too Low
————————————————————————————————————————————————————————————
P113700
DUMMY fault. Not intented for fault
tracing
No Sub Type Information
DUMMY fault. Not intented for fault tracing
DUMMY fault. Not intented for fault tracing
DUMMY fault. Not intented for fault tracing
Check:
DUMMY fault. Not intented for fault tracing
Oil Thermostat
————————————————————————————————————————————————————————————
P113711
Measured voltage below limit
Circuit Short To Ground
Oil thermostat alwaysclosed.
Broken actuator, wire or
ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Oil Thermostat
————————————————————————————————————————————————————————————
P113712
Measured voltage above limit
Circuit Short To Battery
Oil thermostat always open. Increased fuel consumption may be seen.
Broken actuator, wire or ECM driver output Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Oil Thermostat
————————————————————————————————————————————————————————————
P113713
Measured voltage outside the limits specified by the
sensor
Circuit Open
Oil thermostat always open. Increased fuel consumption may be seen.
Broken actuator or wire. Actuator/Harness
Diagnostic Service 14. No additional action is needed
Check: Actuator/Harness
Oil Thermostat
————————————————————————————————————————————————————————————
P011164
Signal Plausibility Failure
None
The boost temperature sensor output is showing either too high or to low value.
(abnormal value) Harness
Sensor
Ambient air temperature sensor.
Diagnostic Service 14. No additional action is needed
Check:
Harness Sensor
Ambient air temperature sensor.
Intake Air Temperature Sensor 1 Circuit Range/Performance Bank 1
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P20E892
Performance or Incorrect Operation
No urea dosing
ACM dosing module: Dosing valve leakage.
Bleed orifice leakage, pressure hose lekage, pump internal leakage, empty ureatank
Tank frozen.
if pump/tank-lines are mixed-up when connecting them to the pump unit there will be no pressure built (check color mar Empty Urea tank, Urea filter clogged, Urea inlet pipe leakage/blocked, Urea tank ventilation, ACM Pump module: Pump
Diagnostic Service 14. No additional action is needed
Check:
Empty Urea tank, Urea filter clogged, Urea inlet pipe leakage/blocked, Urea tank ventilation, ACM Pump module: Pump
Reductant Pressure Too Low
————————————————————————————————————————————————————————————
P21CA00
No Sub Type Information
No dozing
Voltage supply to ACM.
Voltage supply to Urea pump.
Diagnostic Service 14. No additional action is needed
Check:
Voltage supply to Urea pump.
Reductant Control Module Supply Voltage
————————————————————————————————————————————————————————————
P114411
Measured voltage below limit
Circuit Short To Ground
EMS can not control starter
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P114412
Measured voltage
above limit
Circuit Short To Battery
Impossible to activate
starter motor.
Start relay/harness
Diagnostic Service 14. No additional
action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P114413
Measured voltage outside the limits specified by the
sensor
Circuit Open
Impossible to activate starter motor
Start relay/harness
Diagnostic Service 14. No additional action is needed
Check:
Start relay/Harness
Starter Relay Highside
————————————————————————————————————————————————————————————
P116A13
Measured voltage outside the limits specified by the
sensor
Circuit Open
No urea dosing
.
Diagnostic Service 14. No additional action is needed
.
Reductant Pump “A” Control Low Side
————————————————————————————————————————————————————————————
P116B00
Measured voltage below limit
No Sub Type Information
No urea dosing
.
Diagnostic Service 14. No additional action is needed
.
Reductant Pump “A” Control Low Side Circuit
Low
————————————————————————————————————————————————————————————
P116C00
Measured voltage above limit
No Sub Type Information
No urea dosing
.
Diagnostic Service 14. No additional action is needed
.
Reductant Pump “A” Control Low Side Circuit
High
————————————————————————————————————————————————————————————
P021900
No Sub Type Information
Engine speed is limited (to commonly 1200rpm). VCB and EPD activated to lower espd below deactivation limit (commonly 1000rpm).
Engine is/was overspeeding. Engine could be running on oil, due to e.g. faulty crankcase oil filter.
Diagnostic Service 14. No additional action is needed
Check:
Engine could be running on oil, due to e.g. faulty crankcase oil filter.
Engine Overspeed Condition
————————————————————————————————————————————————————————————
P115C00
Measured voltage above limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control
Module Sensor Power Supply “C” Circuit High
————————————————————————————————————————————————————————————
P115D00
Measured voltage below limit
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power
Supply “C” Circuit Low
————————————————————————————————————————————————————————————
P06E970
Actuator Stuck On
The starter motor is deactivated
The starter motor is deactivated due to that the cogwheels of the starter and engine are stuck
None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to that the cogwheels of the starter and engine are stuck
Engine Starter Performance
————————————————————————————————————————————————————————————
P06E998
Component or System Over Temperature
The starter motor is deactivated
The starter motor is deactivated due to overheat None
Diagnostic Service 14. No additional action is needed
Check:
The starter motor is deactivated due to overheat
Engine Starter Performance
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
P115E97
Component or System Operation Obstructed or Blocked
No dozing
Bleed orifice clogged
Bleed orifice, Urea pressure sensor,
Diagnostic Service 14. No additional action is needed
Check:
Bleed orifice, Urea pressure sensor,
Reductant Return No Flow Detected
————————————————————————————————————————————————————————————
P11609B
High/Excessive Flow
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Root Cause Unknown (First Level)
————————————————————————————————————————————————————————————
P116192
Performance or Incorrect Operation
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – Insufficient Reagent Quality (First Level)
————————————————————————————————————————————————————————————
P116300
No Sub Type Information
.
Not possible to erase, will be healed after 400 days. In production, please re- flash the control unit and make sure to enter factory mode next time
.
NOx Exceedence – NOx Control Monitoring System (First Level)
————————————————————————————————————————————————————————————
P26047F
Measured voltage below limit
Actuator Stuck Off
Preheat relay problem or sense SC-.
Shorting wire may break when attempt
Preheat sense 1
Preheat relay
Diagnostic Service 14. No additional action is needed
Check:
Preheat sense 1 Preheat relay
Intake Air Heater “A” Circuit Range/Performance
————————————————————————————————————————————————————————————
P115600
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power Supply “A” Circuit High
————————————————————————————————————————————————————————————
P115700
No Sub Type Information
.
Diagnostic Service 14. No additional action is needed
.
Reductant Control Module Sensor Power Supply “A” Circuit Low
———&#